Wednesday , November 18 2026
Breaking News

CATIA – Computer Aided Design and Drafting Certification Exam Answers 2026 (All 100 Questions)

CATIA – Computer Aided Design and Drafting Certification exam answers 2026: This page lists all 100 questions of the official CATIA – Computer Aided Design and Drafting Certification exam by Itronix Solutions, each with its four answer options and the correct answer highlighted in green. Use it to revise every topic before you attempt the test and earn your verifiable certificate.

About this certification: CATIA stands for Computer Aided Three-Dimensional Interactive Application. It’s much more than a CAD (Computer Aided Design) software package.

Certification CATIA – Computer Aided Design and Drafting Certification
Provider Itronix Solutions
Category Engineering & CAD
Total questions 100 multiple-choice questions
Marks 1 mark per question (100 marks)
Passing score 80% (80 out of 100)
Retake Available if you do not pass
Certificate Verifiable online certificate

Take the exam: CATIA – Computer Aided Design and Drafting Certification on Itronix Solutions. See every other Itronix exam in our complete list of Itronix certification answers.

CATIA – Computer Aided Design and Drafting Exam Questions and Answers

Questions 1 to 25

1. Basic Catia V5: Is "wrench-Bonn?et_string.CATPrpduct" an acceptable filename in Catia?

A. True
B. False ✔

Correct answer: B. False

2. Basic Catia V5: If you are missing a toolbar, what do you do?

A. Close and start Catia again
B. Close the open document and open it again
C. Right-click on an icon and look for it there or check View-Toolbars ✔
D. Start a different module of Catia and look for it there

Correct answer: C. Right-click on an icon and look for it there or check View-Toolbars

3. The basic geometric building blocks provided in a CAD/CAM package are

A. circles
B. lines
C. points
D. all of the mentioned ✔

Correct answer: D. all of the mentioned

4. Using the Relative Polar Coordinate System to add a 3 inch line that is 45 degrees from the end point of the line created above the drafter would ________.

A. type @3<45 and enter ✔
B. type 3 forward slash and enter
C. type 3 back slash and enter
D. type 3 and try to use the Dynamic Input readout to find the end point

Correct answer: A. type @3<45 and enter

5. The software that enables the to implement custom application or modify the system for specialized needs is known as

A. programming software ✔
B. application software
C. operating software
D. graphics software

Correct answer: A. programming software

6. The software that performs the data entry, design, analysis, drafting and manufacturing functions is known as

A. graphics software
B. application software ✔
C. programming software
D. operating software

Correct answer: B. application software

7. The software that is used to provide the users with various functions to perform geometric modelling and construction is known as

A. operating software
B. programming software
C. graphics software ✔
D. application software

Correct answer: C. graphics software

8. The software that is used to control the computer’s work flow, organize its data and perform house keeping functions is known as

A. application software
B. graphics software
C. programming software
D. operating software ✔

Correct answer: D. operating software

9. The function of interpolator in a CNC machine controller is to

A. Control tool rapid approach speed
B. Coordinate feed rates of axes ✔
C. Perform miscellaneous (M) functions (tool change, coolant control etc.)
D. Control spindle speed

Correct answer: B. Coordinate feed rates of axes

10. The basic geometric building blocks provided in a CAD/CAM package are

A. Cricles
B. Lines
C. Points
D. All the above ✔

Correct answer: D. All the above

11. Point to point systems CNC are used for

A. Parting
B. Grooving
C. Reaming ✔
D. Facing

Correct answer: C. Reaming

12. In the CNC machine tool, the part program entered into the computer memory

A. Can be used again and again ✔
B. Can be used only once
C. Can be used again but it has to be modified every time
D. None of the above

Correct answer: A. Can be used again and again

13. The term used by most CAD systems for “rounding corners” is

A. Fillet ✔
B. Curve
C. Chamfer
D. Smooth

Correct answer: A. Fillet

14. When using the TRIM command, which do you select first?

A. The object to be trimmed
B. The cutting edges ✔
C. Nothing
D. Everything

Correct answer: B. The cutting edges

15. Scaling objects makes them

A. Bigger
B. Smaller(
C. It only stretches them
D. Both Bigger and Smaller ✔

Correct answer: D. Both Bigger and Smaller

16. Objects are rotated around the

A. Bottom right of the object
B. Origin
C. Base point ✔
D. Centre of the object

Correct answer: C. Base point

17. The computer-aided design (CAD) hardware doesn’t include.

A. Computer programmes ✔
B. Graphic display terminals
C. Computer
D. Keyboard

Correct answer: A. Computer programmes

18. How many types of CAD are there?

A. 4
B. 5 ✔
C. 6
D. 7

Correct answer: B. 5

19. Modem CAD systems are based on:

A. IFG
B. GCI
C. ICG ✔
D. GIF

Correct answer: C. ICG

20. The computer communicates with the user via:

A. CPU
B. Graphics
C. Display button
D. CRT ✔

Correct answer: D. CRT

21. CATIA is developed by:

A. PTC
B. Autodesk
C. Siemens
D. Dassault Systemes ✔

Correct answer: D. Dassault Systemes

22. CATIA stands for:

A. Computer Assisted Technical Industrial Art
B. Central Automated Tool for Industrial Assembly
C. None
D. Computer Aided Three-dimensional Interactive Application ✔

Correct answer: D. Computer Aided Three-dimensional Interactive Application

23. CATIA is widely used in:

A. Music production
B. Photo editing
C. Aerospace and automotive industries ✔
D. Accounting

Correct answer: C. Aerospace and automotive industries

24. CATIA V5 organises functionality into:

A. Ribbons only
B. Tabs only
C. Plugins only
D. Workbenches ✔

Correct answer: D. Workbenches

25. The specification tree in CATIA shows:

A. Only printers
B. Only colours
C. The history and structure of features and parts ✔
D. Only file names

Correct answer: C. The history and structure of features and parts

Questions 26 to 50

26. The compass in CATIA is used to:

A. Manipulate the view or move components in 3D ✔
B. Print drawings
C. Navigate menus
D. Measure temperature

Correct answer: A. Manipulate the view or move components in 3D

27. The Sketcher workbench is used to:

A. Render images
B. Create 2D profiles for 3D features ✔
C. Assemble parts
D. Create drawings only

Correct answer: B. Create 2D profiles for 3D features

28. A fully constrained sketch in CATIA is shown in:

A. Green ✔
B. White always
C. Purple
D. Red

Correct answer: A. Green

29. An over-constrained sketch is typically shown in:

A. Blue only
B. Green
C. Purple or red ✔
D. Black

Correct answer: C. Purple or red

30. Constraints in Sketcher include:

A. Only layers
B. Dimensional and geometric constraints like coincidence and tangency ✔
C. Only colours
D. Only materials

Correct answer: B. Dimensional and geometric constraints like coincidence and tangency

31. The Part Design workbench is used for:

A. Surface styling only
B. Assembling products
C. Creating solid parts from sketches ✔
D. Drafting only

Correct answer: C. Creating solid parts from sketches

32. A Pad in CATIA:

A. Rotates a sketch
B. Removes material
C. Creates holes only
D. Extrudes a sketch to add material ✔

Correct answer: D. Extrudes a sketch to add material

33. A Pocket in CATIA:

A. Removes material by extruding a sketch ✔
B. Creates a fillet
C. Adds material
D. Creates a shell

Correct answer: A. Removes material by extruding a sketch

34. A Shaft in CATIA:

A. Extrudes linearly
B. Revolves a sketch around an axis to add material ✔
C. Mirrors parts
D. Cuts holes

Correct answer: B. Revolves a sketch around an axis to add material

35. A Groove in CATIA:

A. Creates drafts
B. Revolves a sketch to remove material ✔
C. Adds material
D. Creates ribs

Correct answer: B. Revolves a sketch to remove material

36. The Hole feature in CATIA creates:

A. Standard holes like counterbored or tapped holes ✔
B. Fillets
C. Shells
D. Sketches

Correct answer: A. Standard holes like counterbored or tapped holes

37. Edge Fillet in CATIA:

A. Adds material
B. Removes faces
C. Rounds edges ✔
D. Bevels edges

Correct answer: C. Rounds edges

38. Chamfer in CATIA:

A. Bevels edges ✔
B. Creates holes
C. Rounds edges
D. Extrudes sketches

Correct answer: A. Bevels edges

39. Shell in CATIA:

A. Creates patterns
B. Mirrors a solid
C. Fills a solid
D. Hollows a solid leaving walls of specified thickness ✔

Correct answer: D. Hollows a solid leaving walls of specified thickness

40. Draft Angle in CATIA:

A. Removes material only
B. Rounds edges
C. Adds taper to faces for moulding ✔
D. Creates threads

Correct answer: C. Adds taper to faces for moulding

41. Rib in CATIA:

A. Creates fillets
B. Sweeps a profile along a centre curve to add material ✔
C. Creates holes
D. Removes material only

Correct answer: B. Sweeps a profile along a centre curve to add material

42. Slot in CATIA:

A. Creates patterns
B. Creates drafts
C. Sweeps a profile along a curve to remove material ✔
D. Adds material

Correct answer: C. Sweeps a profile along a curve to remove material

43. Multi-section Solid creates:

A. A single extrusion
B. A fillet
C. A solid blending between multiple sections ✔
D. A hole

Correct answer: C. A solid blending between multiple sections

44. Rectangular Pattern repeats features:

A. Around an axis
B. Along one or two directions ✔
C. Once
D. Randomly

Correct answer: B. Along one or two directions

45. Circular Pattern repeats features:

A. Once only
B. Around an axis ✔
C. In a straight line
D. Randomly

Correct answer: B. Around an axis

46. Mirror in Part Design:

A. Scales features
B. Creates a symmetric copy about a plane ✔
C. Deletes features
D. Rotates features

Correct answer: B. Creates a symmetric copy about a plane

47. Boolean operations in CATIA include:

A. Undo and redo
B. Cut and paste
C. Add, Remove, Intersect and Assemble bodies ✔
D. Print and save

Correct answer: C. Add, Remove, Intersect and Assemble bodies

48. A PartBody is:

A. The main body containing solid features in a part ✔
B. A sketch only
C. An assembly
D. A drawing

Correct answer: A. The main body containing solid features in a part

49. Geometrical Sets store:

A. Only materials
B. Only solids
C. Wireframe and surface elements ✔
D. Only drawings

Correct answer: C. Wireframe and surface elements

50. Generative Shape Design (GSD) is used for:

A. 2D drafting only
B. FEA only
C. Assemblies only
D. Advanced surface modelling ✔

Correct answer: D. Advanced surface modelling

Questions 51 to 75

51. Wireframe elements include:

A. Only solids
B. Only drawings
C. Only materials
D. Points, lines, planes and curves ✔

Correct answer: D. Points, lines, planes and curves

52. Extrude surface in GSD creates:

A. A hole
B. A surface by extruding a profile ✔
C. A drawing
D. A solid

Correct answer: B. A surface by extruding a profile

53. Sweep surface creates:

A. A plane
B. A point
C. A material
D. A surface by moving a profile along a guide ✔

Correct answer: D. A surface by moving a profile along a guide

54. Fill surface creates:

A. A surface patch bounded by curves ✔
B. A hole
C. A solid
D. A line

Correct answer: A. A surface patch bounded by curves

55. Join in GSD:

A. Splits elements
B. Combines multiple surfaces or curves into one element ✔
C. Creates solids directly
D. Deletes surfaces

Correct answer: B. Combines multiple surfaces or curves into one element

56. Split in GSD:

A. Cuts an element using another element ✔
B. Joins surfaces
C. Mirrors curves
D. Creates points

Correct answer: A. Cuts an element using another element

57. Thick Surface converts:

A. A point into a line
B. A solid into a surface
C. A surface into a solid with thickness ✔
D. A sketch into a drawing

Correct answer: C. A surface into a solid with thickness

58. Close Surface creates:

A. A drawing
B. A pattern
C. A sketch
D. A solid from a closed surface volume ✔

Correct answer: D. A solid from a closed surface volume

59. Surface continuity G1 means:

A. Tangent continuity ✔
B. Position continuity only
C. No continuity
D. Curvature continuity

Correct answer: A. Tangent continuity

60. Surface continuity G2 means:

A. Curvature continuity ✔
B. Position only
C. Tangent continuity only
D. No continuity

Correct answer: A. Curvature continuity

61. The Assembly Design workbench is used to:

A. Combine parts into products with constraints ✔
B. Render images
C. Create sketches
D. Draw surfaces

Correct answer: A. Combine parts into products with constraints

62. A Product in CATIA is:

A. A single sketch
B. An assembly containing parts and sub-assemblies ✔
C. A drawing sheet
D. A material

Correct answer: B. An assembly containing parts and sub-assemblies

63. CATIA part files use the extension:

A. .CATPart ✔
B. .CATProduct
C. .CATDrawing
D. .SLDPRT

Correct answer: A. .CATPart

64. CATIA assembly files use the extension:

A. .CATProduct ✔
B. .CATDrawing
C. .CATPart
D. .DWG

Correct answer: A. .CATProduct

65. CATIA drawing files use the extension:

A. .CATProduct
B. .CATDrawing ✔
C. .PDF only
D. .CATPart

Correct answer: B. .CATDrawing

66. Assembly constraints include:

A. Colour and texture
B. Mass and density
C. Coincidence, contact, offset, angle and fix ✔
D. File and folder

Correct answer: C. Coincidence, contact, offset, angle and fix

67. A Fix constraint in assembly:

A. Mirrors a part
B. Allows free movement
C. Locks a component in space ✔
D. Deletes a part

Correct answer: C. Locks a component in space

68. Clash analysis checks:

A. Colours
B. Spelling errors
C. File sizes
D. Interference and contact between components ✔

Correct answer: D. Interference and contact between components

69. Exploded views help to:

A. Show how components fit together ✔
B. Delete parts
C. Hide parts
D. Change materials

Correct answer: A. Show how components fit together

70. Bill of Materials in CATIA lists:

A. Surface continuity
B. Layer names
C. Components and quantities in a product ✔
D. Sketch constraints

Correct answer: C. Components and quantities in a product

71. The Drafting workbench creates:

A. Assemblies
B. 3D surfaces
C. 2D engineering drawings from 3D models ✔
D. FEA results

Correct answer: C. 2D engineering drawings from 3D models

72. Projection views in drawings include:

A. Only text
B. Only 3D renders
C. Front, top, side and isometric views ✔
D. Only exploded views

Correct answer: C. Front, top, side and isometric views

73. Section views in drafting show:

A. Only materials
B. Internal features by cutting through the model ✔
C. Only colours
D. Only external views

Correct answer: B. Internal features by cutting through the model

74. Detail views show:

A. Enlarged portions of a view ✔
B. Exploded views
C. Section only
D. Full assemblies

Correct answer: A. Enlarged portions of a view

75. Associativity means:

A. Nothing is linked
B. Drawings never update
C. Models update from drawings only
D. Drawings update when the 3D model changes ✔

Correct answer: D. Drawings update when the 3D model changes

Questions 76 to 100

76. GD&T annotations in drawings define:

A. Materials only
B. Colours
C. Geometric tolerances such as flatness and position ✔
D. Fonts

Correct answer: C. Geometric tolerances such as flatness and position

77. Knowledgeware in CATIA enables:

A. Only drafting
B. Only printing
C. Only rendering
D. Parameters, formulas and rules to drive designs ✔

Correct answer: D. Parameters, formulas and rules to drive designs

78. Parameters in CATIA can be used to:

A. Control dimensions and create design variants ✔
B. Change colours only
C. Print drawings
D. Delete parts

Correct answer: A. Control dimensions and create design variants

79. Design tables in CATIA link:

A. Drawings to emails
B. Parts to printers
C. Surfaces to materials
D. Parameters to external spreadsheets for configurations ✔

Correct answer: D. Parameters to external spreadsheets for configurations

80. Power Copy in CATIA allows:

A. Deleting features
B. Reusing groups of features with inputs in other parts ✔
C. Copying files only
D. Printing faster

Correct answer: B. Reusing groups of features with inputs in other parts

81. Generative Structural Analysis in CATIA performs:

A. Surface styling
B. Assembly only
C. Drafting
D. Finite element analysis on parts ✔

Correct answer: D. Finite element analysis on parts

82. DMU (Digital Mock-Up) tools are used for:

A. Graphic design
B. Reviewing, simulating and analysing virtual assemblies ✔
C. Accounting
D. Writing code

Correct answer: B. Reviewing, simulating and analysing virtual assemblies

83. Sheet Metal Design in CATIA creates:

A. Drawings only
B. Castings only
C. Parts with walls, bends and flat patterns ✔
D. Surfaces only

Correct answer: C. Parts with walls, bends and flat patterns

84. Weld Design in CATIA is used to:

A. Draw sketches
B. Render images
C. Create surfaces
D. Define welds between parts in assemblies ✔

Correct answer: D. Define welds between parts in assemblies

85. 3DEXPERIENCE platform is:

A. A CAD file
B. Dassault’s collaborative cloud and PLM environment including CATIA ✔
C. A material
D. A printer

Correct answer: B. Dassault’s collaborative cloud and PLM environment including CATIA

86. PLM stands for:

A. Part Layout Model
B. Product Lifecycle Management ✔
C. Primary Load Mechanism
D. Process Line Manufacturing

Correct answer: B. Product Lifecycle Management

87. ENOVIA is used for:

A. Surface modelling
B. Rendering
C. Drafting only
D. Product data and lifecycle management ✔

Correct answer: D. Product data and lifecycle management

88. STEP and IGES formats allow:

A. Spreadsheets
B. Exchanging CAD data with other systems ✔
C. Image editing
D. Audio files

Correct answer: B. Exchanging CAD data with other systems

89. Reference planes in CATIA include:

A. No planes
B. XY, YZ and ZX planes ✔
C. Only one plane
D. Random planes

Correct answer: B. XY, YZ and ZX planes

90. Update (Ctrl+U) in CATIA:

A. Saves files
B. Deletes features
C. Regenerates the model after changes ✔
D. Prints drawings

Correct answer: C. Regenerates the model after changes

91. Measure tools in CATIA can check:

A. File names
B. Colours
C. Distances, angles and inertia properties ✔
D. Spelling

Correct answer: C. Distances, angles and inertia properties

92. Applying materials in CATIA enables:

A. Drafting only
B. Mass calculations and realistic rendering ✔
C. Faster sketching
D. Assemblies only

Correct answer: B. Mass calculations and realistic rendering

93. Good modelling practice in CATIA includes:

A. Fully constraining sketches and organising the tree clearly ✔
B. Leaving sketches unconstrained
C. Random naming
D. Avoiding planes

Correct answer: A. Fully constraining sketches and organising the tree clearly

94. Aerospace companies using CATIA include:

A. Airbus and Boeing ✔
B. Only small shops
C. Only bakeries
D. Only banks

Correct answer: A. Airbus and Boeing

95. The main advantage of CATIA is:

A. Powerful integrated solid, surface and assembly design for complex products ✔
B. Accounting
C. Simple photo editing
D. Email marketing

Correct answer: A. Powerful integrated solid, surface and assembly design for complex products

96. Constraint "Coincidence" in assembly aligns:

A. Axes, planes or points to be coincident ✔
B. Materials
C. File names
D. Colours

Correct answer: A. Axes, planes or points to be coincident

97. Publication in CATIA allows:

A. Printing only
B. Deleting parts
C. Exposing selected geometry for reuse in assemblies ✔
D. Rendering

Correct answer: C. Exposing selected geometry for reuse in assemblies

98. Flexible sub-assemblies allow:

A. Only rendering
B. Sub-assembly components to move independently in the parent ✔
C. Parts to be deleted
D. Nothing to move

Correct answer: B. Sub-assembly components to move independently in the parent

99. The Hide/Show command:

A. Deletes elements
B. Creates elements
C. Controls visibility of elements ✔
D. Renames elements

Correct answer: C. Controls visibility of elements

100. Healing in GSD is used to:

A. Delete curves
B. Create holes
C. Add colours
D. Fix small gaps between surfaces ✔

Correct answer: D. Fix small gaps between surfaces

How to Pass the CATIA – Computer Aided Design and Drafting Exam

  • Read every question carefully; most options look similar, so look for the most precise answer.
  • Revise the questions above topic by topic rather than memorising letters, because option order can change in the live test.
  • You need 80 correct answers out of 100 to pass, so aim to understand at least 85 to stay safe.
  • If you do not clear it on the first attempt, review the questions you missed and use the retake option.

Frequently Asked Questions

How many questions are in the CATIA – Computer Aided Design and Drafting Certification exam?

The exam has 100 multiple-choice questions, each worth 1 mark.

What is the passing score for the CATIA – Computer Aided Design and Drafting Certification?

You need at least 80% (80 out of 100) to pass and receive the certificate.

Can I retake the CATIA – Computer Aided Design and Drafting Certification exam?

Yes. If you score below 80%, you can retry the test after reviewing the topics.

Is the Itronix certificate verifiable?

Yes. Every certificate issued by Itronix Solutions has a unique ID that can be checked on the Itronix verify-certificate page.

More Engineering & CAD Certification Answers

Disclaimer: These answers are provided for learning and revision. Questions and answers are checked regularly; if you find a mistake, let us know in the comments.

About Priya Dogra

Priya Dogra runs priyadogra.com, where she shares free certification courses, internships, jobs, scholarships and exam preparation guides for Indian students and freshers. Follow her on YouTube, LinkedIn and Instagram for the latest opportunities.

Check Also

Unix/ Linux Certification exam answers 2026

Unix/ Linux Certification Exam Answers 2026 (All 100 Questions)

All 100 Unix/ Linux Certification exam questions with correct answers highlighted - updated 2026.

Leave a Reply

Your email address will not be published. Required fields are marked *