Basics of Civil Engineering Certification exam answers 2026: This page lists all 100 questions of the official Basics of Civil Engineering Certification exam by Itronix Solutions, each with its four answer options and the correct answer highlighted in green. Use it to revise every topic before you attempt the test and earn your verifiable certificate.
About this certification: A civil engineer is an engineer who plans and maintains infrastructure projects like airports, roads, dams, and stormwater drainage.
| Certification | Basics of Civil Engineering Certification |
| Provider | Itronix Solutions |
| Category | Engineering & CAD |
| Total questions | 100 multiple-choice questions |
| Marks | 1 mark per question (100 marks) |
| Passing score | 80% (80 out of 100) |
| Retake | Available if you do not pass |
| Certificate | Verifiable online certificate |
Take the exam: Basics of Civil Engineering Certification on Itronix Solutions. See every other Itronix exam in our complete list of Itronix certification answers.
Basics of Civil Engineering Exam Questions and Answers
Questions 1 to 25
1. Stones are obtained from rocks that are made up of:
Correct answer: A. Minerals
2. Which one of the following is not a classification of stones?
Correct answer: B. Mineralogical Classification
3. The hot molten material occurring naturally below the surface of the Earth is called:
Correct answer: C. Magma
4. At what depth and rate is a hypabyssal rock formed?
Correct answer: D. Quick cooling of magma at a shallow depth
5. What is the life time of a moderately durable timber?
Correct answer: A. 5-10 years
6. Which of the following is an example of soft wood?
Correct answer: B. Deodar
7. Which IS Code gives a classification of commercial timbers and their zonal distribution?
Correct answer: C. IS 399
8. Hard wood is strong in tension and weak in compression.
Correct answer: B. False
9. Principal planes are subjected to
Correct answer: A. Normal stresses only
10. A masonry dam (density = 20,000 N/m3) 6 m high, one metre wide at the top and 4 m wide at the base, has vertical water face. The minimum stress at the base of the dam when the reservoir is full, will be
Correct answer: B. 7,500 N/m2
11. A three hinged arch is generally hinged at its supports and
Correct answer: C. A three hinged arch is generally hinged at its supports and
12. Shear strain energy theory for the failure of a material at elastic limit, is due to
Correct answer: A. Von Mises
13. A simply supported rolled steel joist 8 m long carries a uniformly distributed load over it span so that the maximum bending stress is 75 N/mm2. If the slope at the ends is 0.005 radian and the value of E = 0.2 × 106 N/mm2, the depth of the joist, is
Correct answer: B. 400 mm
14. A compound truss may be formed by connecting two simple rigid frames, by
Correct answer: C. Three bars
15. A cantilever of length 2 cm and depth 10 cm tapers in plan from a width 24 cm to zero at its free end. If the modulus of elasticity of the material is 0.2 × 106 N/mm2, the deflection of the free end, is
Correct answer: D. 5 mm
16. The angle between the direction of star and the direction of earth’s axis of rotation is called
Correct answer: A. Co-declination
17. Polaris is usually observed for the determination of the latitude when it is
Correct answer: B. At culmination
18. Pick up the correct statement from the following:
Correct answer: D. All the above
19. The point on the photograph where bisector between the vertical line through optical centre of the camera lens and the plate perpendicular meets, is known as
Correct answer: C. Isocenter
20. The station where observations are not made, but the angles at the station are used in triangulation series, is known as
Correct answer: B. Pivot station
21. Civil engineering deals with:
Correct answer: B. Design, construction and maintenance of infrastructure
22. Branches of civil engineering include:
Correct answer: B. Structural, geotechnical, transportation, environmental and water resources
23. Cement is made mainly from:
Correct answer: A. Limestone and clay heated in a kiln
24. Ordinary Portland Cement sets by:
Correct answer: A. Hydration when mixed with water
25. Concrete is a mixture of:
Correct answer: D. Cement, water, fine aggregate and coarse aggregate
Questions 26 to 50
26. The water-cement ratio affects:
Correct answer: C. Concrete strength and durability
27. A lower water-cement ratio generally gives:
Correct answer: B. Higher strength (with proper workability)
28. Curing of concrete means:
Correct answer: B. Maintaining moisture and temperature for proper strength gain
29. Concrete is strong in:
Correct answer: D. Compression
30. Steel reinforcement in RCC is used because:
Correct answer: B. Concrete is weak in tension
31. RCC stands for:
Correct answer: C. Reinforced Cement Concrete
32. Slump test measures:
Correct answer: C. Workability of fresh concrete
33. Compressive strength of concrete is commonly tested on:
Correct answer: B. Cubes or cylinders after 28 days
34. M20 concrete has a characteristic compressive strength of:
Correct answer: A. 20 MPa (N/mm2)
35. Pre-stressed concrete involves:
Correct answer: B. Introducing compressive stresses before loads are applied
36. Bricks are commonly made from:
Correct answer: C. Clay that is moulded and fired
37. Mortar is a mixture of:
Correct answer: B. Cement or lime, sand and water
38. A load-bearing wall:
Correct answer: D. Supports loads from above
39. A beam primarily resists:
Correct answer: A. Bending
40. A column primarily carries:
Correct answer: A. Axial compressive loads
41. A slab is:
Correct answer: B. A flat horizontal structural element like a floor
42. A cantilever beam is:
Correct answer: D. Fixed at one end and free at the other
43. A simply supported beam is:
Correct answer: A. Supported at both ends without moment restraint
44. Dead load refers to:
Correct answer: A. The permanent weight of the structure itself
45. Live load refers to:
Correct answer: A. Temporary or moving loads such as occupants
46. Wind and seismic loads are examples of:
Correct answer: A. Lateral loads
47. Shear force at a section is:
Correct answer: B. The internal force acting parallel to the cross-section
48. Bending moment causes:
Correct answer: A. A member to bend
49. Stress is defined as:
Correct answer: A. Force per unit area
50. Strain is defined as:
Correct answer: B. Change in length divided by original length
Questions 51 to 75
51. Young’s modulus relates:
Correct answer: B. Stress to strain in the elastic region
52. The factor of safety in design:
Correct answer: D. Provides a margin against failure
53. Foundations transfer:
Correct answer: B. Structural loads safely to the ground
54. Shallow foundations include:
Correct answer: C. Isolated footings and raft foundations
55. Pile foundations are used when:
Correct answer: C. Surface soil is weak and loads must reach deeper strata
56. Bearing capacity of soil is:
Correct answer: A. The maximum load per unit area the soil can support
57. Geotechnical engineering studies:
Correct answer: C. Soil and rock behaviour
58. Soil compaction increases:
Correct answer: A. Density and strength of soil
59. The Atterberg limits include:
Correct answer: D. Liquid limit, plastic limit and shrinkage limit
60. Settlement of foundations refers to:
Correct answer: D. Downward movement due to soil compression
61. Surveying is used to:
Correct answer: D. Measure distances, angles and elevations on land
62. A total station measures:
Correct answer: B. Angles and distances electronically
63. Levelling in surveying determines:
Correct answer: B. Differences in elevation
64. GPS and GNSS in surveying provide:
Correct answer: D. Precise positioning coordinates
65. A contour line connects:
Correct answer: A. Points of equal elevation
66. Transportation engineering deals with:
Correct answer: B. Design and operation of roads, railways and traffic systems
67. Flexible pavements are typically made of:
Correct answer: B. Bituminous (asphalt) layers
68. Rigid pavements are typically made of:
Correct answer: A. Concrete slabs
69. Camber on a road is provided for:
Correct answer: D. Drainage of rainwater
70. Superelevation on curves helps to:
Correct answer: B. Counteract centrifugal force
71. Traffic signals help to:
Correct answer: C. Control conflicting traffic movements safely
72. Water resources engineering includes:
Correct answer: B. Dams, canals, irrigation and flood control
73. A dam is built to:
Correct answer: B. Store water, control floods and generate power
74. Hydrology studies:
Correct answer: C. The occurrence and movement of water on Earth
75. Environmental engineering focuses on:
Correct answer: A. Water treatment, wastewater, air quality and waste management
Questions 76 to 100
76. Potable water must be:
Correct answer: B. Safe for drinking
77. Wastewater treatment removes:
Correct answer: D. Contaminants before discharge or reuse
78. Sedimentation in water treatment:
Correct answer: B. Allows suspended particles to settle
79. Chlorination is used to:
Correct answer: D. Disinfect water by killing pathogens
80. Building codes ensure:
Correct answer: B. Structures meet minimum safety standards
81. Earthquake-resistant design aims to:
Correct answer: D. Provide ductility and prevent collapse during seismic events
82. Estimation in construction calculates:
Correct answer: D. Quantities and costs of materials and work
83. Bill of Quantities (BOQ) lists:
Correct answer: B. Items of work with quantities for pricing
84. Project scheduling in construction can use:
Correct answer: B. Gantt charts and CPM
85. Construction safety requires:
Correct answer: A. Personal protective equipment and safe work practices
86. PPE on construction sites includes:
Correct answer: D. Helmets, safety shoes, gloves and high-visibility vests
87. Formwork is:
Correct answer: A. A temporary mould for shaping concrete
88. Plastering is applied to:
Correct answer: B. Provide a smooth protective finish to walls
89. Damp-proof course (DPC) prevents:
Correct answer: C. Rising moisture into walls
90. Steel structures are joined using:
Correct answer: B. Bolts and welds
91. Bridges types include:
Correct answer: A. Beam, arch, suspension and cable-stayed
92. A suspension bridge carries its deck using:
Correct answer: D. Cables hanging from towers
93. AutoCAD and Revit are used in civil engineering for:
Correct answer: A. Drafting and building information modelling
94. BIM stands for:
Correct answer: A. Building Information Modelling
95. Sustainable construction aims to:
Correct answer: D. Reduce environmental impact and resource use
96. Green building certifications include:
Correct answer: C. LEED and GRIHA
97. The main role of a civil engineer is to:
Correct answer: D. Plan, design and build safe and sustainable infrastructure
98. Aggregates in concrete provide:
Correct answer: D. Bulk, strength and dimensional stability
99. Expansion joints are provided to:
Correct answer: D. Allow movement due to temperature changes
100. A retaining wall is used to:
Correct answer: A. Hold back soil at different ground levels
How to Pass the Basics of Civil Engineering Exam
- Read every question carefully; most options look similar, so look for the most precise answer.
- Revise the questions above topic by topic rather than memorising letters, because option order can change in the live test.
- You need 80 correct answers out of 100 to pass, so aim to understand at least 85 to stay safe.
- If you do not clear it on the first attempt, review the questions you missed and use the retake option.
Frequently Asked Questions
How many questions are in the Basics of Civil Engineering Certification exam?
The exam has 100 multiple-choice questions, each worth 1 mark.
What is the passing score for the Basics of Civil Engineering Certification?
You need at least 80% (80 out of 100) to pass and receive the certificate.
Can I retake the Basics of Civil Engineering Certification exam?
Yes. If you score below 80%, you can retry the test after reviewing the topics.
Is the Itronix certificate verifiable?
Yes. Every certificate issued by Itronix Solutions has a unique ID that can be checked on the Itronix verify-certificate page.
More Engineering & CAD Certification Answers
- ANSYS Structural Analysis Certification Exam Answers
- AutoCAD Certification Exam Answers
- AutoCAD Civil 3D Certification Exam Answers
- CATIA – Computer Aided Design and Drafting Certification Exam Answers
- CNC Operator Certification Exam Answers
- MATLAB Certification Exam Answers
- PLC Programming Certiication Exam Answers
- Robotics Certification Exam Answers
Disclaimer: These answers are provided for learning and revision. Questions and answers are checked regularly; if you find a mistake, let us know in the comments.
Priya Dogra – Free Certifications, Exam Answers & Career Guides Free certification exam answers, courses, scholarships and career guides for learners worldwide