ANSYS Structural Analysis Certification exam answers 2026: This page lists all 100 questions of the official ANSYS Structural Analysis Certification exam by Itronix Solutions, each with its four answer options and the correct answer highlighted in green. Use it to revise every topic before you attempt the test and earn your verifiable certificate.
About this certification: Structural analysis is a branch of solid mechanics which uses simplified models for solids like bars, beams and shells for engineering decision making.
| Certification | ANSYS Structural Analysis Certification |
| Provider | Itronix Solutions |
| Category | Engineering & CAD |
| Total questions | 100 multiple-choice questions |
| Marks | 1 mark per question (100 marks) |
| Passing score | 80% (80 out of 100) |
| Retake | Available if you do not pass |
| Certificate | Verifiable online certificate |
Take the exam: ANSYS Structural Analysis Certification on Itronix Solutions. See every other Itronix exam in our complete list of Itronix certification answers.
ANSYS Structural Analysis Exam Questions and Answers
Questions 1 to 25
1. Which of the following structural loads are not applied commonly to a building?
Correct answer: A. Rain load
2. In the case of a structural member supporting more than one floor with load exceeding 100psf., what is the maximum permitted reduction %?
Correct answer: B. 20
3. Which of the following is statically determinate structure?
Correct answer: C. Double overhanging
4. What does an eigenvector represent in the formulation of Modal Analysis?
Correct answer: D. Mode shape
5. Which numerical method is used by ANSYS to converge a nonlinear solution?
Correct answer: A. Newton-Raphson Method
6. Which of these is NOT a solver in ANSYS?
Correct answer: A. Symmetric Solver
7. Degree of static indeterminacy of a rigid-jointed plane frame having 15 members, 3 reaction components and 14 joints is
Correct answer: B. 6
8. For heavily reinforced concrete member, the nominal maximum size of the aggregates should be restricted to
Correct answer: C. Smaller of A and B
9. The fixed support in a real beam becomes in the conjugate beam a
Correct answer: D. Free end
10. If there are m unknown member forces, r unknown reaction components and j number of joints, then the degree of static indeterminacy of a pin-jointed plane frame is given by
Correct answer: A. m + r – 2j
11. Independent displacement components at each joint of a rigid-jointed plane frame are
Correct answer: C. two linear movements and one rotation
12. If in a pin-jointed plane frame (m + r) > 2j, then the frame is
Correct answer: B. stable and statically indeterminate
13. Castigliano’s first theorem is applicable
Correct answer: C. only when principle of superposition is valid
14. What will be Vmax in the above question if the hospital is made up of structural steel frames?
Correct answer: A. .02813gw
15. Which of the following material is not used in making trusses?
Correct answer: B. Concrete
16. Why is base plate provided in short roof trusses?
Correct answer: C. As provision for temperature related expansion/contraction
17. Stresses and strains calculated on an element at…………
Correct answer: A. Integration points
18. Which of these loads are NOT supported in Harmonic Analysis?
Correct answer: B. Gravity Load
19. What are the mandatory material properties needed for Static Structural Analysis?
Correct answer: A. Young’s Modulus and Poisson’s ratio
20. When a series of wheel loads crosses a simply supported girder, the maximum bending moment under any given wheel load occurs when
Correct answer: B. The centre of span is midway between the centre of gravity of the load system and the wheel load under consideration
21. ANSYS is mainly used for:
Correct answer: B. Engineering simulation such as finite element analysis
22. FEA stands for:
Correct answer: B. Finite Element Analysis
23. FEA works by:
Correct answer: A. Dividing a structure into small elements and solving equations numerically
24. ANSYS Workbench is:
Correct answer: A. A project environment that links geometry, meshing, setup and results
25. ANSYS Mechanical is used for:
Correct answer: D. Structural, thermal and modal analyses
Questions 26 to 50
26. Static structural analysis assumes:
Correct answer: C. Loads are applied slowly and inertia effects are negligible
27. The typical FEA workflow is:
Correct answer: B. Geometry, materials, mesh, boundary conditions, solve and post-process
28. SpaceClaim or DesignModeler in ANSYS is used for:
Correct answer: B. Creating and preparing geometry
29. Engineering Data in Workbench defines:
Correct answer: D. Material properties
30. Young’s modulus is required for:
Correct answer: B. Linear elastic structural analysis
31. Poisson’s ratio describes:
Correct answer: C. Lateral strain relative to axial strain
32. Density is required for:
Correct answer: C. Modal, dynamic and gravity analyses
33. A mesh consists of:
Correct answer: B. Elements connected at nodes
34. Nodes in FEA are:
Correct answer: A. Points where elements connect and results are calculated
35. Common 3D solid element shapes include:
Correct answer: B. Tetrahedra and hexahedra
36. Hexahedral elements are often preferred because they:
Correct answer: C. Can give accurate results with fewer elements
37. A finer mesh generally:
Correct answer: B. Improves accuracy but increases solve time
38. Mesh convergence study checks:
Correct answer: D. That results stop changing significantly as the mesh is refined
39. Element quality metrics include:
Correct answer: A. Skewness, aspect ratio and orthogonal quality
40. Highly skewed elements can cause:
Correct answer: A. Inaccurate results or solver errors
41. Mesh refinement is often applied:
Correct answer: B. At areas of high stress gradients like holes and fillets
42. Boundary conditions define:
Correct answer: D. Supports and loads acting on the model
43. A fixed support constrains:
Correct answer: A. All translational and rotational degrees of freedom
44. A frictionless support allows:
Correct answer: A. Sliding in the plane but no normal movement
45. Remote force allows:
Correct answer: A. Applying a load offset from the geometry
46. Pressure load is applied:
Correct answer: A. Normal to a surface
47. Gravity or standard earth gravity adds:
Correct answer: B. Self-weight loading
48. Over-constraining a model can cause:
Correct answer: A. Unrealistically high stresses near supports
49. Under-constraining a model can cause:
Correct answer: A. Rigid body motion and solver errors
50. Symmetry boundary conditions help to:
Correct answer: B. Reduce model size by modelling only part of a symmetric structure
Questions 51 to 75
51. Equivalent (von Mises) stress is used to:
Correct answer: B. Assess yielding in ductile materials
52. Total deformation shows:
Correct answer: D. Overall displacement magnitude
53. Factor of safety equals:
Correct answer: B. Material strength divided by calculated stress
54. Stress singularities occur at:
Correct answer: C. Sharp re-entrant corners or point loads where stress theoretically becomes infinite
55. Contact in ANSYS defines:
Correct answer: C. How separate bodies interact
56. Bonded contact:
Correct answer: A. Prevents separation and sliding between faces
57. Frictional contact:
Correct answer: C. Allows sliding resisted by a friction coefficient
58. Contact problems are typically:
Correct answer: A. Nonlinear
59. Material nonlinearity includes:
Correct answer: D. Plasticity beyond the yield point
60. Geometric nonlinearity arises from:
Correct answer: D. Large deformations or rotations
61. Large deflection setting accounts for:
Correct answer: D. Changes in stiffness due to large deformations
62. Modal analysis determines:
Correct answer: B. Natural frequencies and mode shapes
63. Resonance occurs when:
Correct answer: B. An excitation frequency matches a natural frequency
64. Harmonic response analysis studies:
Correct answer: D. Response to sinusoidal loads over a frequency range
65. Transient structural analysis studies:
Correct answer: A. Time-varying loads including inertia effects
66. Linear buckling analysis predicts:
Correct answer: B. Critical load factors for structural instability
67. Fatigue analysis estimates:
Correct answer: B. Life of components under cyclic loading
68. An S-N curve relates:
Correct answer: A. Stress amplitude to number of cycles to failure
69. Steady-state thermal analysis computes:
Correct answer: D. Temperature distribution when conditions do not change with time
70. Transient thermal analysis computes:
Correct answer: B. Temperature changes over time
71. Thermal conductivity determines:
Correct answer: C. How easily heat flows through a material
72. Convection boundary condition requires:
Correct answer: B. A film coefficient and ambient temperature
73. Thermal stress results from:
Correct answer: B. Constrained thermal expansion
74. ANSYS Fluent is used for:
Correct answer: C. Computational fluid dynamics (CFD)
75. CFD solves:
Correct answer: A. Fluid flow and heat transfer equations numerically
Questions 76 to 100
76. Reynolds number indicates:
Correct answer: B. Whether flow is likely laminar or turbulent
77. Turbulence models in CFD include:
Correct answer: D. k-epsilon and k-omega SST
78. Inlet and outlet boundary conditions are used in:
Correct answer: B. CFD simulations
79. Residuals in CFD indicate:
Correct answer: D. Convergence of the numerical solution
80. Inflation layers in meshing are used to:
Correct answer: B. Resolve boundary layers near walls
81. ANSYS Maxwell and HFSS are used for:
Correct answer: D. Electromagnetic simulation
82. APDL stands for:
Correct answer: D. ANSYS Parametric Design Language
83. Parameters in Workbench allow:
Correct answer: B. Running design studies by varying inputs
84. Design optimisation in ANSYS aims to:
Correct answer: B. Find designs that best meet objectives within constraints
85. Probes in post-processing are used to:
Correct answer: A. Extract results at specific locations
86. Validation of FEA results involves:
Correct answer: D. Comparing with hand calculations, tests or known solutions
87. Hand calculations help to:
Correct answer: A. Sanity-check simulation results
88. Units consistency in FEA is important because:
Correct answer: B. Inconsistent units give wrong results
89. The principle of Saint-Venant states that:
Correct answer: C. Local load effects diminish away from the load application region
90. Plane stress assumption applies to:
Correct answer: B. Thin plates loaded in their plane
91. Shell elements are suitable for:
Correct answer: A. Thin-walled structures
92. Beam elements are suitable for:
Correct answer: D. Long slender members like frames
93. Hooke’s law states:
Correct answer: A. Stress is proportional to strain in the elastic region
94. Yield strength is:
Correct answer: A. The stress at which permanent deformation begins
95. Ultimate tensile strength is:
Correct answer: D. The maximum stress a material can withstand before necking or failure
96. The main purpose of simulation tools like ANSYS is to:
Correct answer: C. Predict product performance virtually before physical testing
97. Explicit dynamics analysis is suited for:
Correct answer: D. High-speed events like impacts and crashes
98. Coupled field analysis combines:
Correct answer: D. Multiple physics such as thermal and structural
99. Bolt pretension in ANSYS models:
Correct answer: D. Initial clamping force in bolted joints
100. Weak springs in ANSYS can help to:
Correct answer: A. Stabilise under-constrained models
How to Pass the ANSYS Structural Analysis Exam
- Read every question carefully; most options look similar, so look for the most precise answer.
- Revise the questions above topic by topic rather than memorising letters, because option order can change in the live test.
- You need 80 correct answers out of 100 to pass, so aim to understand at least 85 to stay safe.
- If you do not clear it on the first attempt, review the questions you missed and use the retake option.
Frequently Asked Questions
How many questions are in the ANSYS Structural Analysis Certification exam?
The exam has 100 multiple-choice questions, each worth 1 mark.
What is the passing score for the ANSYS Structural Analysis Certification?
You need at least 80% (80 out of 100) to pass and receive the certificate.
Can I retake the ANSYS Structural Analysis Certification exam?
Yes. If you score below 80%, you can retry the test after reviewing the topics.
Is the Itronix certificate verifiable?
Yes. Every certificate issued by Itronix Solutions has a unique ID that can be checked on the Itronix verify-certificate page.
More Engineering & CAD Certification Answers
- AutoCAD Certification Exam Answers
- AutoCAD Civil 3D Certification Exam Answers
- Basics of Civil Engineering Certification Exam Answers
- CATIA – Computer Aided Design and Drafting Certification Exam Answers
- CNC Operator Certification Exam Answers
- MATLAB Certification Exam Answers
- PLC Programming Certiication Exam Answers
- Robotics Certification Exam Answers
Disclaimer: These answers are provided for learning and revision. Questions and answers are checked regularly; if you find a mistake, let us know in the comments.
Priya Dogra – Free Certifications, Exam Answers & Career Guides Free certification exam answers, courses, scholarships and career guides for learners worldwide