PLC Programming Certiication exam answers 2026: This page lists all 100 questions of the official PLC Programming Certiication exam by Itronix Solutions, each with its four answer options and the correct answer highlighted in green. Use it to revise every topic before you attempt the test and earn your verifiable certificate.
About this certification: Ladder Logic is the most common language used in PLC programming. It was developed to mimic relay logic, that is why the syntax is very simple.
| Certification | PLC Programming Certiication |
| Provider | Itronix Solutions |
| Category | Engineering & CAD |
| Total questions | 100 multiple-choice questions |
| Marks | 1 mark per question (100 marks) |
| Passing score | 80% (80 out of 100) |
| Retake | Available if you do not pass |
| Certificate | Verifiable online certificate |
Take the exam: PLC Programming Certiication on Itronix Solutions. See every other Itronix exam in our complete list of Itronix certification answers.
PLC Programming Certiication Exam Questions and Answers
Questions 1 to 25
1. Ladder logic programming consists primarily of:
Correct answer: A. Virtual relay contacts and coils
2. In a PLC, the scan time refers to the amount of time in which …..
Correct answer: D. the entire program takes to execute
3. The difference between online and offline PLC programming is . . .
Correct answer: A. where the edited program resides
4. In PLC programming, a retentive function is one that:
Correct answer: C. Is not reset after a power cycle
5. What is the primary purpose of a PLC?
Correct answer: D. All of the above
6. What type of programming language is typically used to program a PLC?
Correct answer: C. Ladder Logic
7. How many maximum input and output points does a high-end PLC have?
Correct answer: C. 64 input, 64 output
8. What type of power supply is typically used for a PLC?
Correct answer: C. Both AC and DC
9. When ___________ contacts are actuated, they disrupt the power supply through them.
Correct answer: B. normally closed type
10. Normally open contacts are open
Correct answer: A. when input is not energized
11. The type of memory which is fast and temporarily stores the data which are immediately required for use is called as______
Correct answer: C. RAM
12. How is the speed of operation of the conventional relay system compared to digital controllers?
Correct answer: C. Very slow
13. What is the largest integer number that a PLC counter function can reach if it uses a 16 bit register?
Correct answer: B. 65,535
14. An OR function implemented in ladder logic uses:
Correct answer: D. Normally-open contacts in parallel
15. A good application for a timed interrupt in a PLC program would be:
Correct answer: B. A PID function block
16. What is the main function of the CPU in a PLC?
Correct answer: C. To execute the program and control the input and output devices
17. How does a PLC differ from a traditional hardwired control system?
Correct answer: A. PLCs use software programming instead of physical wiring.
18. What is the function of the input/output (I/O) module in a PLC?
Correct answer: C. To interface with the input and output devices
19. The capability of convention relay systems for complex operations is ___________ that of the PLCs.
Correct answer: B. poor than
20. PLC can be ___________ in plant to change the sequence of operation.
Correct answer: C. programmed and reprogrammed
21. PLC stands for:
Correct answer: B. Programmable Logic Controller
22. A PLC is mainly used for:
Correct answer: B. Automating industrial machines and processes
23. The PLC scan cycle consists of:
Correct answer: A. Reading inputs, executing the program and updating outputs
24. Ladder logic is:
Correct answer: A. A graphical PLC programming language resembling relay circuits
25. IEC 61131-3 defines:
Correct answer: D. Standard PLC programming languages
Questions 26 to 50
26. PLC languages under IEC 61131-3 include:
Correct answer: C. Ladder Diagram, Function Block Diagram, Structured Text, Instruction List and SFC
27. A normally open (NO) contact in ladder logic:
Correct answer: B. Passes power when the associated input is true
28. A normally closed (NC) contact in ladder logic:
Correct answer: B. Passes power when the associated input is false
29. A coil in ladder logic represents:
Correct answer: D. An output or internal bit
30. A seal-in (latching) circuit:
Correct answer: B. Keeps an output on after a momentary start button is released
31. A TON timer:
Correct answer: C. Turns on its output after a preset delay when enabled
32. A TOF timer:
Correct answer: C. Keeps the output on for a delay after the input turns off
33. A counter (CTU) in a PLC:
Correct answer: B. Increments each time its input transitions true
34. Digital inputs to a PLC include:
Correct answer: A. Push buttons, limit switches and proximity sensors
35. Analogue inputs commonly use signals such as:
Correct answer: B. 4-20 mA or 0-10 V
36. The 4-20 mA standard uses 4 mA as:
Correct answer: C. The live zero to detect wire breaks
37. A sinking input and sourcing input describe:
Correct answer: B. The direction of current flow in DC input circuits
38. HMI stands for:
Correct answer: D. Human Machine Interface
39. SCADA systems are used to:
Correct answer: A. Supervise and control industrial processes over large areas
40. Common industrial communication protocols include:
Correct answer: A. Modbus, PROFINET and EtherNet/IP
41. A VFD (Variable Frequency Drive) controls:
Correct answer: B. The speed of an AC motor by varying frequency
42. A relay is:
Correct answer: D. An electrically operated switch
43. A contactor is used for:
Correct answer: A. Switching high-current loads such as motors
44. An emergency stop circuit should be:
Correct answer: A. Hard-wired and fail-safe
45. Lockout/tagout procedures are used to:
Correct answer: A. Ensure machines are safely de-energised during maintenance
46. PID control stands for:
Correct answer: A. Proportional, Integral, Derivative
47. The integral term in PID helps to:
Correct answer: B. Eliminate steady-state error
48. The derivative term in PID responds to:
Correct answer: A. The rate of change of error
49. Open-loop control:
Correct answer: A. Does not use feedback
50. Closed-loop control:
Correct answer: B. Uses feedback to correct output
Questions 51 to 75
51. A proximity sensor detects:
Correct answer: B. Objects without physical contact
52. An encoder measures:
Correct answer: D. Position or speed of rotation
53. A robot is:
Correct answer: B. A programmable machine capable of performing tasks automatically
54. An industrial robot arm’s joints are often described by:
Correct answer: C. Degrees of freedom
55. Common industrial robot types include:
Correct answer: C. Articulated, SCARA, delta and Cartesian
56. SCARA robots are well suited for:
Correct answer: A. Fast pick-and-place and assembly in a horizontal plane
57. Collaborative robots (cobots) are designed to:
Correct answer: C. Work safely alongside humans
58. The end effector of a robot is:
Correct answer: A. The tool at the end of the arm, such as a gripper
59. Forward kinematics calculates:
Correct answer: D. The end-effector position from joint angles
60. Inverse kinematics calculates:
Correct answer: D. Joint angles needed to reach a target position
61. A teach pendant is used to:
Correct answer: D. Program and jog robots manually
62. Robot sensors include:
Correct answer: B. Cameras, lidar, force sensors and encoders
63. Lidar measures distance using:
Correct answer: B. Laser light
64. SLAM in mobile robotics is used for:
Correct answer: D. Building a map while tracking the robot’s position
65. ROS stands for:
Correct answer: A. Robot Operating System
66. Stepper motors are useful because they:
Correct answer: B. Move in precise fixed steps
67. Servo motors provide:
Correct answer: B. Precise position control using feedback
68. CNC stands for:
Correct answer: A. Computer Numerical Control
69. CNC machines are used to:
Correct answer: D. Automatically control machining tools such as lathes and mills
70. G-code is:
Correct answer: B. The programming language commanding CNC machine motion
71. G00 typically commands:
Correct answer: C. Rapid positioning
72. G01 typically commands:
Correct answer: B. Linear interpolation at feed rate
73. G02 and G03 command:
Correct answer: B. Circular interpolation clockwise and counter-clockwise
74. M-codes in CNC control:
Correct answer: C. Miscellaneous machine functions like spindle and coolant
75. M03 typically means:
Correct answer: A. Spindle on clockwise
Questions 76 to 100
76. M30 typically means:
Correct answer: B. Program end and rewind
77. Feed rate in CNC is:
Correct answer: D. The speed at which the tool moves through the material
78. Spindle speed is measured in:
Correct answer: B. RPM (revolutions per minute)
79. Work offset (e.g. G54) defines:
Correct answer: D. The program zero relative to machine coordinates
80. Tool length offset compensates for:
Correct answer: B. Different tool lengths
81. A CNC lathe is used mainly for:
Correct answer: D. Turning cylindrical parts
82. A CNC milling machine uses:
Correct answer: D. A rotating cutter to remove material
83. CAM software is used to:
Correct answer: B. Generate toolpaths and G-code from CAD models
84. Dry run or simulation before machining helps to:
Correct answer: B. Detect collisions and program errors
85. Cutting fluid (coolant) helps to:
Correct answer: A. Reduce heat and improve tool life and finish
86. Machine safety guards protect operators from:
Correct answer: D. Moving parts, chips and coolant
87. Preventive maintenance helps to:
Correct answer: A. Reduce unplanned downtime
88. Industry 4.0 refers to:
Correct answer: B. Smart manufacturing using connected systems, data and automation
89. OEE stands for:
Correct answer: C. Overall Equipment Effectiveness
90. OEE combines:
Correct answer: B. Availability, performance and quality
91. A safety PLC is designed for:
Correct answer: A. Safety-critical functions with redundancy
92. Ladder logic rungs are executed:
Correct answer: D. From top to bottom, left to right during each scan
93. Simulation software for PLCs lets engineers:
Correct answer: A. Test programs without real hardware
94. Documentation of PLC programs should include:
Correct answer: A. Comments, tag descriptions and I/O lists
95. The main purpose of industrial automation is to:
Correct answer: D. Improve productivity, quality and safety through controlled machines
96. A photoelectric sensor detects objects using:
Correct answer: C. A light beam
97. A solenoid valve is used to:
Correct answer: D. Control the flow of fluid electrically
98. Pneumatic systems use:
Correct answer: D. Compressed air to create motion
99. Hydraulic systems use:
Correct answer: D. Pressurised fluid to generate force
100. A limit switch is used to:
Correct answer: A. Detect the end of travel of a moving part
How to Pass the PLC Programming Certiication Exam
- Read every question carefully; most options look similar, so look for the most precise answer.
- Revise the questions above topic by topic rather than memorising letters, because option order can change in the live test.
- You need 80 correct answers out of 100 to pass, so aim to understand at least 85 to stay safe.
- If you do not clear it on the first attempt, review the questions you missed and use the retake option.
Frequently Asked Questions
How many questions are in the PLC Programming Certiication exam?
The exam has 100 multiple-choice questions, each worth 1 mark.
What is the passing score for the PLC Programming Certiication?
You need at least 80% (80 out of 100) to pass and receive the certificate.
Can I retake the PLC Programming Certiication exam?
Yes. If you score below 80%, you can retry the test after reviewing the topics.
Is the Itronix certificate verifiable?
Yes. Every certificate issued by Itronix Solutions has a unique ID that can be checked on the Itronix verify-certificate page.
More Engineering & CAD Certification Answers
- ANSYS Structural Analysis Certification Exam Answers
- AutoCAD Certification Exam Answers
- AutoCAD Civil 3D Certification Exam Answers
- Basics of Civil Engineering Certification Exam Answers
- CATIA – Computer Aided Design and Drafting Certification Exam Answers
- CNC Operator Certification Exam Answers
- MATLAB Certification Exam Answers
- Robotics Certification Exam Answers
Disclaimer: These answers are provided for learning and revision. Questions and answers are checked regularly; if you find a mistake, let us know in the comments.
Priya Dogra – Free Certifications, Exam Answers & Career Guides Free certification exam answers, courses, scholarships and career guides for learners worldwide