Wednesday , November 18 2026
Breaking News

Basics of Civil Engineering Certification Exam Answers 2026 (All 100 Questions)

Basics of Civil Engineering Certification exam answers 2026: This page lists all 100 questions of the official Basics of Civil Engineering Certification exam by Itronix Solutions, each with its four answer options and the correct answer highlighted in green. Use it to revise every topic before you attempt the test and earn your verifiable certificate.

About this certification: A civil engineer is an engineer who plans and maintains infrastructure projects like airports, roads, dams, and stormwater drainage.

Certification Basics of Civil Engineering Certification
Provider Itronix Solutions
Category Engineering & CAD
Total questions 100 multiple-choice questions
Marks 1 mark per question (100 marks)
Passing score 80% (80 out of 100)
Retake Available if you do not pass
Certificate Verifiable online certificate

Take the exam: Basics of Civil Engineering Certification on Itronix Solutions. See every other Itronix exam in our complete list of Itronix certification answers.

Basics of Civil Engineering Exam Questions and Answers

Questions 1 to 25

1. Stones are obtained from rocks that are made up of:

A. Minerals ✔
B. Chemical compounds
C. Crystals
D. Ores

Correct answer: A. Minerals

2. Which one of the following is not a classification of stones?

A. Physical Classification
B. Mineralogical Classification ✔
C. Chemical Classification
D. Practical Classification

Correct answer: B. Mineralogical Classification

3. The hot molten material occurring naturally below the surface of the Earth is called:

A. Lava
B. Slag
C. Magma ✔
D. Tuff

Correct answer: C. Magma

4. At what depth and rate is a hypabyssal rock formed?

A. Rapid cooling of magma at Earth’s surface
B. Rapid cooling of magma at a shallow depth
C. Slow cooling of magma at considerable depth
D. Quick cooling of magma at a shallow depth ✔

Correct answer: D. Quick cooling of magma at a shallow depth

5. What is the life time of a moderately durable timber?

A. 5-10 years ✔
B. 10-15 years
C. 1-5 years
D. 10-20 years

Correct answer: A. 5-10 years

6. Which of the following is an example of soft wood?

A. Oak
B. Deodar ✔
C. Mahogany
D. Sal

Correct answer: B. Deodar

7. Which IS Code gives a classification of commercial timbers and their zonal distribution?

A. IS 190
B. IS 620
C. IS 399 ✔
D. IS 401

Correct answer: C. IS 399

8. Hard wood is strong in tension and weak in compression.

A. True
B. False ✔

Correct answer: B. False

9. Principal planes are subjected to

A. Normal stresses only ✔
B. Tangential stresses only
C. Normal stresses as well as tangential stresses
D. None of these

Correct answer: A. Normal stresses only

10. A masonry dam (density = 20,000 N/m3) 6 m high, one metre wide at the top and 4 m wide at the base, has vertical water face. The minimum stress at the base of the dam when the reservoir is full, will be

A. 750 N/m2
B. 7,500 N/m2 ✔
C. 75,000 N/m2
D. 75 N/m2

Correct answer: B. 7,500 N/m2

11. A three hinged arch is generally hinged at its supports and

A. At one quarter span
B. At the crown
C. A three hinged arch is generally hinged at its supports and ✔
D. None of these

Correct answer: C. A three hinged arch is generally hinged at its supports and

12. Shear strain energy theory for the failure of a material at elastic limit, is due to

A. Von Mises ✔
B. St. Venant
C. Guest or Trecas
D. Rankine

Correct answer: A. Von Mises

13. A simply supported rolled steel joist 8 m long carries a uniformly distributed load over it span so that the maximum bending stress is 75 N/mm2. If the slope at the ends is 0.005 radian and the value of E = 0.2 × 106 N/mm2, the depth of the joist, is

A. 200 mm
B. 400 mm ✔
C. 300 mm
D. 250 mm

Correct answer: B. 400 mm

14. A compound truss may be formed by connecting two simple rigid frames, by

A. Three bars intersecting at a point
B. Two bars
C. Three bars ✔
D. Three parallel bars

Correct answer: C. Three bars

15. A cantilever of length 2 cm and depth 10 cm tapers in plan from a width 24 cm to zero at its free end. If the modulus of elasticity of the material is 0.2 × 106 N/mm2, the deflection of the free end, is

A. 2 mm
B. 3 mm
C. 4 mm
D. 5 mm ✔

Correct answer: D. 5 mm

16. The angle between the direction of star and the direction of earth’s axis of rotation is called

A. Co-declination ✔
B. Co-latitude
C. Declination
D. Latitude

Correct answer: A. Co-declination

17. Polaris is usually observed for the determination of the latitude when it is

A. At elongation
B. At culmination ✔
C. Neither at culmination nor at elongation
D. Either at culmination or at elongation

Correct answer: B. At culmination

18. Pick up the correct statement from the following:

A. The complement of the altitude of star is called the zenith distance of the star
B. The angle between the direction of star in vertical plane and the direction of the star in horizontal plane is called the altitude of the star
C. The vertical plane containing the zenith, the station of observation and the celestial pole is the observer’s meridian plane
D. All the above ✔

Correct answer: D. All the above

19. The point on the photograph where bisector between the vertical line through optical centre of the camera lens and the plate perpendicular meets, is known as

A. Perspective centre
B. Principal point
C. Isocenter ✔
D. Plumb point

Correct answer: C. Isocenter

20. The station where observations are not made, but the angles at the station are used in triangulation series, is known as

A. Satellite station
B. Pivot station ✔
C. Main station
D. Subsidiary station

Correct answer: B. Pivot station

21. Civil engineering deals with:

A. Only electronics
B. Design, construction and maintenance of infrastructure ✔
C. Only chemicals
D. Only software

Correct answer: B. Design, construction and maintenance of infrastructure

22. Branches of civil engineering include:

A. Only electrical
B. Structural, geotechnical, transportation, environmental and water resources ✔
C. Only mechanical
D. Only software

Correct answer: B. Structural, geotechnical, transportation, environmental and water resources

23. Cement is made mainly from:

A. Limestone and clay heated in a kiln ✔
B. Sand only
C. Steel
D. Glass

Correct answer: A. Limestone and clay heated in a kiln

24. Ordinary Portland Cement sets by:

A. Hydration when mixed with water ✔
B. Drying only in sunlight
C. Freezing
D. Burning

Correct answer: A. Hydration when mixed with water

25. Concrete is a mixture of:

A. Steel and wood
B. Glass and plastic
C. Only cement and water
D. Cement, water, fine aggregate and coarse aggregate ✔

Correct answer: D. Cement, water, fine aggregate and coarse aggregate

Questions 26 to 50

26. The water-cement ratio affects:

A. Soil type
B. Steel rusting only
C. Concrete strength and durability ✔
D. Concrete colour only

Correct answer: C. Concrete strength and durability

27. A lower water-cement ratio generally gives:

A. Lower strength
B. Higher strength (with proper workability) ✔
C. Faster rotting
D. No change

Correct answer: B. Higher strength (with proper workability)

28. Curing of concrete means:

A. Painting concrete
B. Maintaining moisture and temperature for proper strength gain ✔
C. Drying quickly in heat
D. Breaking concrete

Correct answer: B. Maintaining moisture and temperature for proper strength gain

29. Concrete is strong in:

A. Bending without reinforcement
B. Tension
C. Torsion only
D. Compression ✔

Correct answer: D. Compression

30. Steel reinforcement in RCC is used because:

A. Steel looks better
B. Concrete is weak in tension ✔
C. Steel is cheaper than concrete
D. Concrete is weak in compression

Correct answer: B. Concrete is weak in tension

31. RCC stands for:

A. Road Construction Code
B. Reinforced Clay Composite
C. Reinforced Cement Concrete ✔
D. Rapid Cement Construction

Correct answer: C. Reinforced Cement Concrete

32. Slump test measures:

A. Soil moisture
B. Steel strength
C. Workability of fresh concrete ✔
D. Strength of hardened concrete

Correct answer: C. Workability of fresh concrete

33. Compressive strength of concrete is commonly tested on:

A. Soil samples
B. Cubes or cylinders after 28 days ✔
C. Steel bars
D. Bricks only

Correct answer: B. Cubes or cylinders after 28 days

34. M20 concrete has a characteristic compressive strength of:

A. 20 MPa (N/mm2) ✔
B. 20 kN
C. 200 MPa
D. 2 MPa

Correct answer: A. 20 MPa (N/mm2)

35. Pre-stressed concrete involves:

A. Adding water later
B. Introducing compressive stresses before loads are applied ✔
C. Only wood
D. No steel

Correct answer: B. Introducing compressive stresses before loads are applied

36. Bricks are commonly made from:

A. Glass
B. Plastic only
C. Clay that is moulded and fired ✔
D. Steel

Correct answer: C. Clay that is moulded and fired

37. Mortar is a mixture of:

A. Cement and gravel only
B. Cement or lime, sand and water ✔
C. Clay and glass
D. Steel and sand

Correct answer: B. Cement or lime, sand and water

38. A load-bearing wall:

A. Is always glass
B. Is only decorative
C. Carries no load
D. Supports loads from above ✔

Correct answer: D. Supports loads from above

39. A beam primarily resists:

A. Bending ✔
B. Only torsion
C. Only compression
D. No loads

Correct answer: A. Bending

40. A column primarily carries:

A. Axial compressive loads ✔
B. No loads
C. Only bending
D. Only tension

Correct answer: A. Axial compressive loads

41. A slab is:

A. A beam only
B. A flat horizontal structural element like a floor ✔
C. A foundation pile
D. A vertical column

Correct answer: B. A flat horizontal structural element like a floor

42. A cantilever beam is:

A. Not supported
B. A column
C. Supported at both ends
D. Fixed at one end and free at the other ✔

Correct answer: D. Fixed at one end and free at the other

43. A simply supported beam is:

A. Supported at both ends without moment restraint ✔
B. A column
C. Fixed at one end only
D. Free at both ends

Correct answer: A. Supported at both ends without moment restraint

44. Dead load refers to:

A. The permanent weight of the structure itself ✔
B. Moving people and furniture
C. Wind only
D. Earthquakes only

Correct answer: A. The permanent weight of the structure itself

45. Live load refers to:

A. Temporary or moving loads such as occupants ✔
B. The structure’s own weight
C. Soil weight only
D. Permanent fixtures

Correct answer: A. Temporary or moving loads such as occupants

46. Wind and seismic loads are examples of:

A. Lateral loads ✔
B. Static vertical loads only
C. No loads
D. Dead loads only

Correct answer: A. Lateral loads

47. Shear force at a section is:

A. Axial force only
B. The internal force acting parallel to the cross-section ✔
C. Torsion
D. Bending moment

Correct answer: B. The internal force acting parallel to the cross-section

48. Bending moment causes:

A. A member to bend ✔
B. A member to twist only
C. No deformation
D. Only compression

Correct answer: A. A member to bend

49. Stress is defined as:

A. Force per unit area ✔
B. Force times length
C. Mass per volume
D. Length per unit time

Correct answer: A. Force per unit area

50. Strain is defined as:

A. Force per area
B. Change in length divided by original length ✔
C. Weight per volume
D. Area per length

Correct answer: B. Change in length divided by original length

Questions 51 to 75

51. Young’s modulus relates:

A. Force to time
B. Stress to strain in the elastic region ✔
C. Load to area only
D. Mass to volume

Correct answer: B. Stress to strain in the elastic region

52. The factor of safety in design:

A. Is not needed
B. Reduces strength
C. Increases load
D. Provides a margin against failure ✔

Correct answer: D. Provides a margin against failure

53. Foundations transfer:

A. Electricity
B. Structural loads safely to the ground ✔
C. Heat
D. Water to buildings

Correct answer: B. Structural loads safely to the ground

54. Shallow foundations include:

A. Piles only
B. Wells only
C. Isolated footings and raft foundations ✔
D. Caissons only

Correct answer: C. Isolated footings and raft foundations

55. Pile foundations are used when:

A. Only for roads
B. No loads exist
C. Surface soil is weak and loads must reach deeper strata ✔
D. Soil is very strong near the surface

Correct answer: C. Surface soil is weak and loads must reach deeper strata

56. Bearing capacity of soil is:

A. The maximum load per unit area the soil can support ✔
B. Soil age
C. Soil moisture only
D. Soil colour

Correct answer: A. The maximum load per unit area the soil can support

57. Geotechnical engineering studies:

A. Steel design
B. Traffic flow
C. Soil and rock behaviour ✔
D. Water treatment only

Correct answer: C. Soil and rock behaviour

58. Soil compaction increases:

A. Density and strength of soil ✔
B. Settlement
C. Voids
D. Water content always

Correct answer: A. Density and strength of soil

59. The Atterberg limits include:

A. Speed limits
B. Strength limits
C. Load limits
D. Liquid limit, plastic limit and shrinkage limit ✔

Correct answer: D. Liquid limit, plastic limit and shrinkage limit

60. Settlement of foundations refers to:

A. Horizontal sliding only
B. Cracking of paint
C. Upward movement only
D. Downward movement due to soil compression ✔

Correct answer: D. Downward movement due to soil compression

61. Surveying is used to:

A. Write software
B. Mix concrete
C. Design circuits
D. Measure distances, angles and elevations on land ✔

Correct answer: D. Measure distances, angles and elevations on land

62. A total station measures:

A. Only weight
B. Angles and distances electronically ✔
C. Only temperature
D. Only soil type

Correct answer: B. Angles and distances electronically

63. Levelling in surveying determines:

A. Concrete strength
B. Differences in elevation ✔
C. Soil strength
D. Horizontal distances only

Correct answer: B. Differences in elevation

64. GPS and GNSS in surveying provide:

A. Steel grades
B. Concrete mix designs
C. Water quality
D. Precise positioning coordinates ✔

Correct answer: D. Precise positioning coordinates

65. A contour line connects:

A. Points of equal elevation ✔
B. Roads
C. Points of equal temperature
D. Rivers only

Correct answer: A. Points of equal elevation

66. Transportation engineering deals with:

A. Only buildings
B. Design and operation of roads, railways and traffic systems ✔
C. Only electronics
D. Only water supply

Correct answer: B. Design and operation of roads, railways and traffic systems

67. Flexible pavements are typically made of:

A. Concrete slabs only
B. Bituminous (asphalt) layers ✔
C. Steel plates
D. Glass

Correct answer: B. Bituminous (asphalt) layers

68. Rigid pavements are typically made of:

A. Concrete slabs ✔
B. Gravel only
C. Soil only
D. Asphalt only

Correct answer: A. Concrete slabs

69. Camber on a road is provided for:

A. Decoration
B. Parking
C. Speed increase
D. Drainage of rainwater ✔

Correct answer: D. Drainage of rainwater

70. Superelevation on curves helps to:

A. Store water
B. Counteract centrifugal force ✔
C. Increase skidding
D. Reduce visibility

Correct answer: B. Counteract centrifugal force

71. Traffic signals help to:

A. Store vehicles
B. Slow all traffic permanently
C. Control conflicting traffic movements safely ✔
D. Increase accidents

Correct answer: C. Control conflicting traffic movements safely

72. Water resources engineering includes:

A. Only roads
B. Dams, canals, irrigation and flood control ✔
C. Only bridges
D. Only buildings

Correct answer: B. Dams, canals, irrigation and flood control

73. A dam is built to:

A. Carry traffic only
B. Store water, control floods and generate power ✔
C. Build houses
D. Dry rivers

Correct answer: B. Store water, control floods and generate power

74. Hydrology studies:

A. Soil colour
B. Traffic signals
C. The occurrence and movement of water on Earth ✔
D. Steel rusting only

Correct answer: C. The occurrence and movement of water on Earth

75. Environmental engineering focuses on:

A. Water treatment, wastewater, air quality and waste management ✔
B. Only steel
C. Only bridges
D. Only roads

Correct answer: A. Water treatment, wastewater, air quality and waste management

Questions 76 to 100

76. Potable water must be:

A. Untreated always
B. Safe for drinking ✔
C. Salty
D. Coloured

Correct answer: B. Safe for drinking

77. Wastewater treatment removes:

A. Nothing
B. Only odour
C. Only colour
D. Contaminants before discharge or reuse ✔

Correct answer: D. Contaminants before discharge or reuse

78. Sedimentation in water treatment:

A. Adds colour
B. Allows suspended particles to settle ✔
C. Heats water
D. Adds chlorine

Correct answer: B. Allows suspended particles to settle

79. Chlorination is used to:

A. Add minerals
B. Increase turbidity
C. Colour water
D. Disinfect water by killing pathogens ✔

Correct answer: D. Disinfect water by killing pathogens

80. Building codes ensure:

A. Faster construction only
B. Structures meet minimum safety standards ✔
C. Lower costs only
D. Decorative styles

Correct answer: B. Structures meet minimum safety standards

81. Earthquake-resistant design aims to:

A. Remove foundations
B. Ignore lateral loads
C. Make buildings rigid only
D. Provide ductility and prevent collapse during seismic events ✔

Correct answer: D. Provide ductility and prevent collapse during seismic events

82. Estimation in construction calculates:

A. Traffic speed
B. Soil colour
C. Water quality
D. Quantities and costs of materials and work ✔

Correct answer: D. Quantities and costs of materials and work

83. Bill of Quantities (BOQ) lists:

A. Employee names
B. Items of work with quantities for pricing ✔
C. Soil tests
D. Design drawings only

Correct answer: B. Items of work with quantities for pricing

84. Project scheduling in construction can use:

A. Weather reports
B. Gantt charts and CPM ✔
C. Recipes
D. Only guesswork

Correct answer: B. Gantt charts and CPM

85. Construction safety requires:

A. Personal protective equipment and safe work practices ✔
B. No helmets
C. Working alone always
D. Ignoring hazards

Correct answer: A. Personal protective equipment and safe work practices

86. PPE on construction sites includes:

A. Formal suits
B. Sandals
C. Jewellery
D. Helmets, safety shoes, gloves and high-visibility vests ✔

Correct answer: D. Helmets, safety shoes, gloves and high-visibility vests

87. Formwork is:

A. A temporary mould for shaping concrete ✔
B. Permanent wall finish
C. A foundation
D. Steel reinforcement

Correct answer: A. A temporary mould for shaping concrete

88. Plastering is applied to:

A. Reinforce beams
B. Provide a smooth protective finish to walls ✔
C. Lay roads
D. Make foundations

Correct answer: B. Provide a smooth protective finish to walls

89. Damp-proof course (DPC) prevents:

A. Wind loads
B. Earthquakes
C. Rising moisture into walls ✔
D. Fire spread only

Correct answer: C. Rising moisture into walls

90. Steel structures are joined using:

A. Rope
B. Bolts and welds ✔
C. Glue only
D. Nails only

Correct answer: B. Bolts and welds

91. Bridges types include:

A. Beam, arch, suspension and cable-stayed ✔
B. Only wooden
C. Only floating
D. Only tunnels

Correct answer: A. Beam, arch, suspension and cable-stayed

92. A suspension bridge carries its deck using:

A. Columns every metre
B. Arches only
C. Solid walls
D. Cables hanging from towers ✔

Correct answer: D. Cables hanging from towers

93. AutoCAD and Revit are used in civil engineering for:

A. Drafting and building information modelling ✔
B. Photo editing
C. Accounting
D. Email

Correct answer: A. Drafting and building information modelling

94. BIM stands for:

A. Building Information Modelling ✔
B. Bridge Inspection Method
C. Building Inventory Map
D. Basic Infrastructure Management

Correct answer: A. Building Information Modelling

95. Sustainable construction aims to:

A. Ignore energy use
B. Increase waste
C. Use more water
D. Reduce environmental impact and resource use ✔

Correct answer: D. Reduce environmental impact and resource use

96. Green building certifications include:

A. HTML
B. ISO 9001 only
C. LEED and GRIHA ✔
D. PCI DSS

Correct answer: C. LEED and GRIHA

97. The main role of a civil engineer is to:

A. Write software only
B. Manage social media
C. Design fashion
D. Plan, design and build safe and sustainable infrastructure ✔

Correct answer: D. Plan, design and build safe and sustainable infrastructure

98. Aggregates in concrete provide:

A. Water only
B. Colour only
C. Electricity
D. Bulk, strength and dimensional stability ✔

Correct answer: D. Bulk, strength and dimensional stability

99. Expansion joints are provided to:

A. Decorate surfaces
B. Increase load
C. Store water
D. Allow movement due to temperature changes ✔

Correct answer: D. Allow movement due to temperature changes

100. A retaining wall is used to:

A. Hold back soil at different ground levels ✔
B. Support bridges only
C. Store water only
D. Carry roofs

Correct answer: A. Hold back soil at different ground levels

How to Pass the Basics of Civil Engineering Exam

  • Read every question carefully; most options look similar, so look for the most precise answer.
  • Revise the questions above topic by topic rather than memorising letters, because option order can change in the live test.
  • You need 80 correct answers out of 100 to pass, so aim to understand at least 85 to stay safe.
  • If you do not clear it on the first attempt, review the questions you missed and use the retake option.

Frequently Asked Questions

How many questions are in the Basics of Civil Engineering Certification exam?

The exam has 100 multiple-choice questions, each worth 1 mark.

What is the passing score for the Basics of Civil Engineering Certification?

You need at least 80% (80 out of 100) to pass and receive the certificate.

Can I retake the Basics of Civil Engineering Certification exam?

Yes. If you score below 80%, you can retry the test after reviewing the topics.

Is the Itronix certificate verifiable?

Yes. Every certificate issued by Itronix Solutions has a unique ID that can be checked on the Itronix verify-certificate page.

More Engineering & CAD Certification Answers

Disclaimer: These answers are provided for learning and revision. Questions and answers are checked regularly; if you find a mistake, let us know in the comments.

About Priya Dogra

Priya Dogra runs priyadogra.com, where she shares free certification courses, internships, jobs, scholarships and exam preparation guides for Indian students and freshers. Follow her on YouTube, LinkedIn and Instagram for the latest opportunities.

Check Also

Unix/ Linux Certification exam answers 2026

Unix/ Linux Certification Exam Answers 2026 (All 100 Questions)

All 100 Unix/ Linux Certification exam questions with correct answers highlighted - updated 2026.

Leave a Reply

Your email address will not be published. Required fields are marked *