Wednesday , November 18 2026
Breaking News

ANSYS Structural Analysis Certification Exam Answers 2026 (All 100 Questions)

ANSYS Structural Analysis Certification exam answers 2026: This page lists all 100 questions of the official ANSYS Structural Analysis Certification exam by Itronix Solutions, each with its four answer options and the correct answer highlighted in green. Use it to revise every topic before you attempt the test and earn your verifiable certificate.

About this certification: Structural analysis is a branch of solid mechanics which uses simplified models for solids like bars, beams and shells for engineering decision making.

Certification ANSYS Structural Analysis Certification
Provider Itronix Solutions
Category Engineering & CAD
Total questions 100 multiple-choice questions
Marks 1 mark per question (100 marks)
Passing score 80% (80 out of 100)
Retake Available if you do not pass
Certificate Verifiable online certificate

Take the exam: ANSYS Structural Analysis Certification on Itronix Solutions. See every other Itronix exam in our complete list of Itronix certification answers.

ANSYS Structural Analysis Exam Questions and Answers

Questions 1 to 25

1. Which of the following structural loads are not applied commonly to a building?

A. Rain load ✔
B. Environmental load
C. Live load
D. Dead load

Correct answer: A. Rain load

2. In the case of a structural member supporting more than one floor with load exceeding 100psf., what is the maximum permitted reduction %?

A. 15
B. 20 ✔
C. 25
D. 30

Correct answer: B. 20

3. Which of the following is statically determinate structure?

A. Fixed beam
B. Two hinged arch
C. Double overhanging ✔
D. Continuous beam

Correct answer: C. Double overhanging

4. What does an eigenvector represent in the formulation of Modal Analysis?

A. Forcing frequency
B. Phase angle
C. Natural frequency
D. Mode shape ✔

Correct answer: D. Mode shape

5. Which numerical method is used by ANSYS to converge a nonlinear solution?

A. Newton-Raphson Method ✔
B. Bisection Method
C. Taylor’s Method
D. Euler Method

Correct answer: A. Newton-Raphson Method

6. Which of these is NOT a solver in ANSYS?

A. Symmetric Solver ✔
B. PCG Solver
C. Direct Solver
D. Iterative Solver

Correct answer: A. Symmetric Solver

7. Degree of static indeterminacy of a rigid-jointed plane frame having 15 members, 3 reaction components and 14 joints is

A. 5
B. 6 ✔
C. 7
D. 8

Correct answer: B. 6

8. For heavily reinforced concrete member, the nominal maximum size of the aggregates should be restricted to

A. 5 mm less than the minimum clear distance between the main bars
B. 5 mm less than the minimum cover to the reinforcement
C. Smaller of A and B ✔
D. Greater of A and B

Correct answer: C. Smaller of A and B

9. The fixed support in a real beam becomes in the conjugate beam a

A. Fixed support
B. Hinged support
C. Roller support
D. Free end ✔

Correct answer: D. Free end

10. If there are m unknown member forces, r unknown reaction components and j number of joints, then the degree of static indeterminacy of a pin-jointed plane frame is given by

A. m + r – 2j ✔
B. m + r – 3j
C. m + r + 2j
D. m – r + 2j

Correct answer: A. m + r – 2j

11. Independent displacement components at each joint of a rigid-jointed plane frame are

A. one linear movement and two rotations
B. three rotations
C. two linear movements and one rotation ✔
D. three linear movements

Correct answer: C. two linear movements and one rotation

12. If in a pin-jointed plane frame (m + r) > 2j, then the frame is

A. unstable
B. stable and statically indeterminate ✔
C. stable and statically determinate
D. none of the above

Correct answer: B. stable and statically indeterminate

13. Castigliano’s first theorem is applicable

A. when the system behaves elastically
B. for statically determinate structures only
C. only when principle of superposition is valid ✔
D. none of the above

Correct answer: C. only when principle of superposition is valid

14. What will be Vmax in the above question if the hospital is made up of structural steel frames?

A. .02813gw ✔
B. .03813gw
C. 04813gw
D. .01813gw

Correct answer: A. .02813gw

15. Which of the following material is not used in making trusses?

A. Metal bars
B. Concrete ✔
C. Wooden struts
D. Channel

Correct answer: B. Concrete

16. Why is base plate provided in short roof trusses?

A. For stability
B. For rigidity
C. As provision for temperature related expansion/contraction ✔
D. To transmit load effectively

Correct answer: C. As provision for temperature related expansion/contraction

17. Stresses and strains calculated on an element at…………

A. Integration points ✔
B. Nodes
C. Element center
D. All of the above

Correct answer: A. Integration points

18. Which of these loads are NOT supported in Harmonic Analysis?

A. Pressure
B. Gravity Load ✔
C. Moment
D. All of the above

Correct answer: B. Gravity Load

19. What are the mandatory material properties needed for Static Structural Analysis?

A. Young’s Modulus and Poisson’s ratio ✔
B. Young’s Modulus and Yield strength
C. Ultimate strength and Yield Strength
D. Yield Strength and Poisson’s ratio

Correct answer: A. Young’s Modulus and Poisson’s ratio

20. When a series of wheel loads crosses a simply supported girder, the maximum bending moment under any given wheel load occurs when

A. The centre of gravity of the load system is midway between the centre of span and wheel load under consi-deration
B. The centre of span is midway between the centre of gravity of the load system and the wheel load under consideration ✔
C. The wheel load under consideration is midway between the centre of span and the centre of gravity of the load system
D. None of the above

Correct answer: B. The centre of span is midway between the centre of gravity of the load system and the wheel load under consideration

21. ANSYS is mainly used for:

A. Photo editing
B. Engineering simulation such as finite element analysis ✔
C. Accounting
D. Word processing

Correct answer: B. Engineering simulation such as finite element analysis

22. FEA stands for:

A. Final Engineering Assessment
B. Finite Element Analysis ✔
C. Fixed Equation Algorithm
D. Force Estimation Approach

Correct answer: B. Finite Element Analysis

23. FEA works by:

A. Dividing a structure into small elements and solving equations numerically ✔
B. Testing only physical prototypes
C. Guessing results
D. Drawing sketches only

Correct answer: A. Dividing a structure into small elements and solving equations numerically

24. ANSYS Workbench is:

A. A project environment that links geometry, meshing, setup and results ✔
B. A CAD drawing tool only
C. A web browser
D. A spreadsheet

Correct answer: A. A project environment that links geometry, meshing, setup and results

25. ANSYS Mechanical is used for:

A. Electrical circuits only
B. Web design
C. Fluid flow only
D. Structural, thermal and modal analyses ✔

Correct answer: D. Structural, thermal and modal analyses

Questions 26 to 50

26. Static structural analysis assumes:

A. Only heat
B. Only vibration
C. Loads are applied slowly and inertia effects are negligible ✔
D. Loads change rapidly

Correct answer: C. Loads are applied slowly and inertia effects are negligible

27. The typical FEA workflow is:

A. Solve then draw geometry
B. Geometry, materials, mesh, boundary conditions, solve and post-process ✔
C. Results then geometry
D. Mesh only

Correct answer: B. Geometry, materials, mesh, boundary conditions, solve and post-process

28. SpaceClaim or DesignModeler in ANSYS is used for:

A. Solving equations
B. Creating and preparing geometry ✔
C. Plotting results only
D. Writing reports

Correct answer: B. Creating and preparing geometry

29. Engineering Data in Workbench defines:

A. Results
B. Mesh size only
C. Boundary conditions
D. Material properties ✔

Correct answer: D. Material properties

30. Young’s modulus is required for:

A. Mesh generation only
B. Linear elastic structural analysis ✔
C. Licensing
D. Colour selection

Correct answer: B. Linear elastic structural analysis

31. Poisson’s ratio describes:

A. Thermal conductivity
B. Yield strength
C. Lateral strain relative to axial strain ✔
D. Density

Correct answer: C. Lateral strain relative to axial strain

32. Density is required for:

A. Only static analysis with no gravity
B. Only meshing
C. Modal, dynamic and gravity analyses ✔
D. Only colour

Correct answer: C. Modal, dynamic and gravity analyses

33. A mesh consists of:

A. Only text
B. Elements connected at nodes ✔
C. Only lines
D. Only surfaces without nodes

Correct answer: B. Elements connected at nodes

34. Nodes in FEA are:

A. Points where elements connect and results are calculated ✔
B. Materials
C. Loads only
D. Geometry files

Correct answer: A. Points where elements connect and results are calculated

35. Common 3D solid element shapes include:

A. Lines only
B. Tetrahedra and hexahedra ✔
C. Triangles only
D. Circles only

Correct answer: B. Tetrahedra and hexahedra

36. Hexahedral elements are often preferred because they:

A. Never fail
B. Require no nodes
C. Can give accurate results with fewer elements ✔
D. Are always easier to mesh

Correct answer: C. Can give accurate results with fewer elements

37. A finer mesh generally:

A. Reduces accuracy
B. Improves accuracy but increases solve time ✔
C. Always reduces time
D. Removes the need for loads

Correct answer: B. Improves accuracy but increases solve time

38. Mesh convergence study checks:

A. File size
B. Load direction
C. Material colour
D. That results stop changing significantly as the mesh is refined ✔

Correct answer: D. That results stop changing significantly as the mesh is refined

39. Element quality metrics include:

A. Skewness, aspect ratio and orthogonal quality ✔
B. File size only
C. Colour and font
D. Licence type

Correct answer: A. Skewness, aspect ratio and orthogonal quality

40. Highly skewed elements can cause:

A. Inaccurate results or solver errors ✔
B. No effect
C. Better accuracy
D. Faster convergence always

Correct answer: A. Inaccurate results or solver errors

41. Mesh refinement is often applied:

A. Nowhere
B. At areas of high stress gradients like holes and fillets ✔
C. Randomly
D. Only on flat faces

Correct answer: B. At areas of high stress gradients like holes and fillets

42. Boundary conditions define:

A. Mesh density only
B. Units only
C. Material colours
D. Supports and loads acting on the model ✔

Correct answer: D. Supports and loads acting on the model

43. A fixed support constrains:

A. All translational and rotational degrees of freedom ✔
B. Only temperature
C. Nothing
D. Only rotation

Correct answer: A. All translational and rotational degrees of freedom

44. A frictionless support allows:

A. Sliding in the plane but no normal movement ✔
B. No movement at all
C. Free movement in all directions
D. Only rotation

Correct answer: A. Sliding in the plane but no normal movement

45. Remote force allows:

A. Applying a load offset from the geometry ✔
B. Only point loads on nodes
C. Only pressure
D. Only temperature

Correct answer: A. Applying a load offset from the geometry

46. Pressure load is applied:

A. Normal to a surface ✔
B. At one node only
C. As a temperature
D. Along an edge only

Correct answer: A. Normal to a surface

47. Gravity or standard earth gravity adds:

A. Vibration
B. Self-weight loading ✔
C. Contact
D. Thermal loading

Correct answer: B. Self-weight loading

48. Over-constraining a model can cause:

A. Unrealistically high stresses near supports ✔
B. Lower stresses always
C. No effect
D. Better accuracy always

Correct answer: A. Unrealistically high stresses near supports

49. Under-constraining a model can cause:

A. Rigid body motion and solver errors ✔
B. Perfect results
C. Lower stresses
D. Faster solves

Correct answer: A. Rigid body motion and solver errors

50. Symmetry boundary conditions help to:

A. Increase model size
B. Reduce model size by modelling only part of a symmetric structure ✔
C. Ignore materials
D. Remove loads

Correct answer: B. Reduce model size by modelling only part of a symmetric structure

Questions 51 to 75

51. Equivalent (von Mises) stress is used to:

A. Assess brittle fracture only
B. Assess yielding in ductile materials ✔
C. Measure mass
D. Measure temperature

Correct answer: B. Assess yielding in ductile materials

52. Total deformation shows:

A. Temperature
B. Stress
C. Mass
D. Overall displacement magnitude ✔

Correct answer: D. Overall displacement magnitude

53. Factor of safety equals:

A. Mass divided by volume
B. Material strength divided by calculated stress ✔
C. Load divided by area
D. Stress divided by strength

Correct answer: B. Material strength divided by calculated stress

54. Stress singularities occur at:

A. Smooth flat areas
B. Nowhere
C. Sharp re-entrant corners or point loads where stress theoretically becomes infinite ✔
D. Everywhere

Correct answer: C. Sharp re-entrant corners or point loads where stress theoretically becomes infinite

55. Contact in ANSYS defines:

A. Solver type only
B. Mesh density
C. How separate bodies interact ✔
D. Material colour

Correct answer: C. How separate bodies interact

56. Bonded contact:

A. Prevents separation and sliding between faces ✔
B. Ignores bodies
C. Allows sliding without friction
D. Allows free separation

Correct answer: A. Prevents separation and sliding between faces

57. Frictional contact:

A. Bonds bodies
B. Prevents any movement
C. Allows sliding resisted by a friction coefficient ✔
D. Ignores contact

Correct answer: C. Allows sliding resisted by a friction coefficient

58. Contact problems are typically:

A. Nonlinear ✔
B. Purely thermal
C. Always linear
D. Not solvable

Correct answer: A. Nonlinear

59. Material nonlinearity includes:

A. Mesh density
B. Linear elastic only
C. Geometry size
D. Plasticity beyond the yield point ✔

Correct answer: D. Plasticity beyond the yield point

60. Geometric nonlinearity arises from:

A. Material colour
B. Fine mesh
C. Small displacements only
D. Large deformations or rotations ✔

Correct answer: D. Large deformations or rotations

61. Large deflection setting accounts for:

A. Mesh quality
B. Material colour
C. Temperature
D. Changes in stiffness due to large deformations ✔

Correct answer: D. Changes in stiffness due to large deformations

62. Modal analysis determines:

A. Temperature
B. Natural frequencies and mode shapes ✔
C. Static stress only
D. Fluid flow

Correct answer: B. Natural frequencies and mode shapes

63. Resonance occurs when:

A. Mesh is fine
B. An excitation frequency matches a natural frequency ✔
C. Temperature rises
D. Loads are static

Correct answer: B. An excitation frequency matches a natural frequency

64. Harmonic response analysis studies:

A. Heat transfer only
B. Static loads only
C. Fluid flow
D. Response to sinusoidal loads over a frequency range ✔

Correct answer: D. Response to sinusoidal loads over a frequency range

65. Transient structural analysis studies:

A. Time-varying loads including inertia effects ✔
B. Only modes
C. Only static loads
D. Only buckling

Correct answer: A. Time-varying loads including inertia effects

66. Linear buckling analysis predicts:

A. Natural frequencies
B. Critical load factors for structural instability ✔
C. Fatigue life only
D. Heat flow

Correct answer: B. Critical load factors for structural instability

67. Fatigue analysis estimates:

A. Static strength only
B. Life of components under cyclic loading ✔
C. Natural frequency
D. Thermal expansion

Correct answer: B. Life of components under cyclic loading

68. An S-N curve relates:

A. Stress amplitude to number of cycles to failure ✔
B. Stress to density
C. Load to time only
D. Strain to temperature

Correct answer: A. Stress amplitude to number of cycles to failure

69. Steady-state thermal analysis computes:

A. Time-dependent temperature
B. Vibration
C. Stress only
D. Temperature distribution when conditions do not change with time ✔

Correct answer: D. Temperature distribution when conditions do not change with time

70. Transient thermal analysis computes:

A. Modes
B. Temperature changes over time ✔
C. Steady temperatures only
D. Stresses only

Correct answer: B. Temperature changes over time

71. Thermal conductivity determines:

A. Colour
B. Density
C. How easily heat flows through a material ✔
D. Material stiffness

Correct answer: C. How easily heat flows through a material

72. Convection boundary condition requires:

A. Only displacement
B. A film coefficient and ambient temperature ✔
C. Only pressure
D. Only mesh size

Correct answer: B. A film coefficient and ambient temperature

73. Thermal stress results from:

A. Pure pressure loads only
B. Constrained thermal expansion ✔
C. Material colour
D. Mesh refinement

Correct answer: B. Constrained thermal expansion

74. ANSYS Fluent is used for:

A. Structural FEA only
B. Accounting
C. Computational fluid dynamics (CFD) ✔
D. PCB layout

Correct answer: C. Computational fluid dynamics (CFD)

75. CFD solves:

A. Fluid flow and heat transfer equations numerically ✔
B. Only geometry
C. Only stress equations
D. Only circuits

Correct answer: A. Fluid flow and heat transfer equations numerically

Questions 76 to 100

76. Reynolds number indicates:

A. Material strength
B. Whether flow is likely laminar or turbulent ✔
C. Heat capacity
D. Mesh quality

Correct answer: B. Whether flow is likely laminar or turbulent

77. Turbulence models in CFD include:

A. Ohm’s law
B. Hooke’s law
C. von Mises
D. k-epsilon and k-omega SST ✔

Correct answer: D. k-epsilon and k-omega SST

78. Inlet and outlet boundary conditions are used in:

A. Buckling only
B. CFD simulations ✔
C. Modal analysis only
D. Static stress only

Correct answer: B. CFD simulations

79. Residuals in CFD indicate:

A. Material strength
B. Mesh element count
C. Geometry size
D. Convergence of the numerical solution ✔

Correct answer: D. Convergence of the numerical solution

80. Inflation layers in meshing are used to:

A. Remove the mesh
B. Resolve boundary layers near walls ✔
C. Add materials
D. Apply loads

Correct answer: B. Resolve boundary layers near walls

81. ANSYS Maxwell and HFSS are used for:

A. Graphics
B. Accounting
C. Structural FEA
D. Electromagnetic simulation ✔

Correct answer: D. Electromagnetic simulation

82. APDL stands for:

A. Automated Part Design Library
B. Advanced Plot Drawing Language
C. Analysis Program Data Log
D. ANSYS Parametric Design Language ✔

Correct answer: D. ANSYS Parametric Design Language

83. Parameters in Workbench allow:

A. Changing colours
B. Running design studies by varying inputs ✔
C. Licensing
D. Deleting results

Correct answer: B. Running design studies by varying inputs

84. Design optimisation in ANSYS aims to:

A. Ignore loads
B. Find designs that best meet objectives within constraints ✔
C. Remove materials
D. Increase weight always

Correct answer: B. Find designs that best meet objectives within constraints

85. Probes in post-processing are used to:

A. Extract results at specific locations ✔
B. Change geometry
C. Apply loads
D. Create meshes

Correct answer: A. Extract results at specific locations

86. Validation of FEA results involves:

A. Ignoring physics
B. Trusting colours only
C. Skipping checks
D. Comparing with hand calculations, tests or known solutions ✔

Correct answer: D. Comparing with hand calculations, tests or known solutions

87. Hand calculations help to:

A. Sanity-check simulation results ✔
B. Replace all simulations always
C. Draw geometry
D. Create meshes

Correct answer: A. Sanity-check simulation results

88. Units consistency in FEA is important because:

A. Solvers ignore units
B. Inconsistent units give wrong results ✔
C. Only for colours
D. Units do not matter

Correct answer: B. Inconsistent units give wrong results

89. The principle of Saint-Venant states that:

A. Loads have no effect
B. Stress is uniform everywhere
C. Local load effects diminish away from the load application region ✔
D. Mesh is irrelevant

Correct answer: C. Local load effects diminish away from the load application region

90. Plane stress assumption applies to:

A. Electrical circuits
B. Thin plates loaded in their plane ✔
C. Very thick bodies
D. Fluids

Correct answer: B. Thin plates loaded in their plane

91. Shell elements are suitable for:

A. Thin-walled structures ✔
B. Massive solid blocks
C. Fluids only
D. Cables only

Correct answer: A. Thin-walled structures

92. Beam elements are suitable for:

A. Electrical components
B. Thin plates
C. Fluid volumes
D. Long slender members like frames ✔

Correct answer: D. Long slender members like frames

93. Hooke’s law states:

A. Stress is proportional to strain in the elastic region ✔
B. Strain is zero
C. Stress is constant
D. Force equals mass

Correct answer: A. Stress is proportional to strain in the elastic region

94. Yield strength is:

A. The stress at which permanent deformation begins ✔
B. The density
C. The stiffness
D. The breaking strength

Correct answer: A. The stress at which permanent deformation begins

95. Ultimate tensile strength is:

A. Elastic modulus
B. The yield point
C. Poisson’s ratio
D. The maximum stress a material can withstand before necking or failure ✔

Correct answer: D. The maximum stress a material can withstand before necking or failure

96. The main purpose of simulation tools like ANSYS is to:

A. Write documents
B. Replace engineering judgement
C. Predict product performance virtually before physical testing ✔
D. Design logos

Correct answer: C. Predict product performance virtually before physical testing

97. Explicit dynamics analysis is suited for:

A. Slow static loads
B. Modal analysis
C. Steady heat flow
D. High-speed events like impacts and crashes ✔

Correct answer: D. High-speed events like impacts and crashes

98. Coupled field analysis combines:

A. Only meshing
B. Only one load
C. Only materials
D. Multiple physics such as thermal and structural ✔

Correct answer: D. Multiple physics such as thermal and structural

99. Bolt pretension in ANSYS models:

A. Bolt length only
B. Bolt colour
C. Bolt cost
D. Initial clamping force in bolted joints ✔

Correct answer: D. Initial clamping force in bolted joints

100. Weak springs in ANSYS can help to:

A. Stabilise under-constrained models ✔
B. Delete contacts
C. Refine mesh
D. Increase stress

Correct answer: A. Stabilise under-constrained models

How to Pass the ANSYS Structural Analysis Exam

  • Read every question carefully; most options look similar, so look for the most precise answer.
  • Revise the questions above topic by topic rather than memorising letters, because option order can change in the live test.
  • You need 80 correct answers out of 100 to pass, so aim to understand at least 85 to stay safe.
  • If you do not clear it on the first attempt, review the questions you missed and use the retake option.

Frequently Asked Questions

How many questions are in the ANSYS Structural Analysis Certification exam?

The exam has 100 multiple-choice questions, each worth 1 mark.

What is the passing score for the ANSYS Structural Analysis Certification?

You need at least 80% (80 out of 100) to pass and receive the certificate.

Can I retake the ANSYS Structural Analysis Certification exam?

Yes. If you score below 80%, you can retry the test after reviewing the topics.

Is the Itronix certificate verifiable?

Yes. Every certificate issued by Itronix Solutions has a unique ID that can be checked on the Itronix verify-certificate page.

More Engineering & CAD Certification Answers

Disclaimer: These answers are provided for learning and revision. Questions and answers are checked regularly; if you find a mistake, let us know in the comments.

About Priya Dogra

Priya Dogra runs priyadogra.com, where she shares free certification courses, internships, jobs, scholarships and exam preparation guides for Indian students and freshers. Follow her on YouTube, LinkedIn and Instagram for the latest opportunities.

Check Also

Unix/ Linux Certification exam answers 2026

Unix/ Linux Certification Exam Answers 2026 (All 100 Questions)

All 100 Unix/ Linux Certification exam questions with correct answers highlighted - updated 2026.

Leave a Reply

Your email address will not be published. Required fields are marked *