PCB Design Professional Certification exam answers 2026: This page lists all 100 questions of the official PCB Design Professional Certification exam by Itronix Solutions, each with its four answer options and the correct answer highlighted in green. Use it to revise every topic before you attempt the test and earn your verifiable certificate.
About this certification: Learn to design printed circuit boards (PCBs) with this certification. It covers PCB layout, signal integrity, and manufacturing processes. Gain expertise in schematic design, component placement, and testing.
| Certification | PCB Design Professional Certification |
| Provider | Itronix Solutions |
| Category | Electronics & Hardware |
| Total questions | 100 multiple-choice questions |
| Marks | 1 mark per question (100 marks) |
| Passing score | 80% (80 out of 100) |
| Retake | Available if you do not pass |
| Certificate | Verifiable online certificate |
Take the exam: PCB Design Professional Certification on Itronix Solutions. See every other Itronix exam in our complete list of Itronix certification answers.
PCB Design Exam Questions and Answers
Questions 1 to 25
1. What does PCB stand for?
Correct answer: A. A) Printed Circuit Board
2. Which material is most commonly used as the base for a PCB?
Correct answer: C. C) FR4 (Fiberglass Reinforced Epoxy)
3. What is the purpose of vias in a PCB?
Correct answer: C. C) To create electrical connections between different layers of the PCB
4. What is the primary function of a solder mask on a PCB?
Correct answer: B. B) To protect the copper traces from oxidation and short circuits
5. What type of PCB is used when high flexibility is required?
Correct answer: B. B) Flexible PCB
6. What is the standard copper thickness for most PCBs?
Correct answer: A. A) 1 oz/ft²
7. What is the primary purpose of a ground plane in a PCB?
Correct answer: A. A) To reduce electrical noise and provide a return path for signals
8. What is the function of a silkscreen layer on a PCB?
Correct answer: A. A) To provide component labels and markings
9. What does SMT stand for in PCB design?
Correct answer: D. D) Surface Mount Technology
10. What is the primary advantage of using a multi-layer PCB?
Correct answer: C. C) Higher component density and reduced noise
11. What type of PCB defect is caused by improper soldering?
Correct answer: C. C) Cold Joint
12. What does the term "trace width" refer to in PCB design?
Correct answer: C. C) The width of the copper conductor
13. What is the primary reason for using a solder paste in SMT assembly?
Correct answer: D. D) To create electrical and mechanical connections during reflow soldering
14. What is the purpose of a decoupling capacitor in a PCB design?
Correct answer: B. B) To filter noise and stabilize the power supply
15. What is the function of a thermal relief in a PCB?
Correct answer: C. C) To facilitate better heat dissipation
16. Which software is widely used for PCB design?
Correct answer: B. B) Altium Designer
17. What does a "netlist" represent in PCB design?
Correct answer: D. D) The electrical connections between components
18. What is the purpose of a via fill in high-frequency PCBs?
Correct answer: D. D) To improve signal integrity and heat dissipation
19. What type of PCB is commonly used in high-power applications?
Correct answer: B. B) Metal Core PCB
20. What is the function of an impedance-controlled trace in a high-frequency PCB?
Correct answer: C. C) To maintain consistent signal integrity
21. A printed circuit board (PCB) is:
Correct answer: C. A board that mechanically supports and electrically connects components with copper traces
22. The PCB design workflow typically starts with:
Correct answer: B. Schematic capture
23. A schematic symbol represents:
Correct answer: C. A component’s electrical connections
24. A footprint (land pattern) defines:
Correct answer: D. The copper pads and outline for mounting a component on the PCB
25. A netlist describes:
Correct answer: D. Which component pins are connected together
Questions 26 to 50
26. Electrical Rule Check (ERC) in a schematic detects:
Correct answer: B. Unconnected pins and conflicting outputs
27. Design Rule Check (DRC) in a layout detects:
Correct answer: A. Spacing, width and clearance violations
28. FR-4 is:
Correct answer: B. The most common glass-reinforced epoxy PCB substrate
29. Standard PCB thickness is commonly:
Correct answer: A. 1.6 mm
30. Copper thickness is often specified in:
Correct answer: D. Ounces per square foot, e.g. 1 oz
31. A two-layer PCB has:
Correct answer: A. Copper on top and bottom layers
32. Multilayer PCBs allow:
Correct answer: B. Dedicated power and ground planes and denser routing
33. A typical four-layer stackup is:
Correct answer: B. Signal, ground, power, signal
34. A via is:
Correct answer: C. A plated hole connecting traces on different layers
35. Through-hole vias go:
Correct answer: D. Through all layers of the board
36. Blind vias connect:
Correct answer: A. An outer layer to one or more inner layers without passing through
37. Buried vias connect:
Correct answer: B. Inner layers only, not visible from outside
38. Microvias are used in:
Correct answer: B. High-density interconnect (HDI) boards
39. Solder mask is:
Correct answer: C. A protective coating that prevents solder bridges and oxidation
40. Silkscreen is used for:
Correct answer: B. Printing reference designators, labels and logos
41. Reference designators such as R1, C5 and U3 identify:
Correct answer: B. Individual components on the board
42. Surface finishes such as HASL, ENIG and OSP:
Correct answer: C. Protect exposed copper pads and aid soldering
43. ENIG finish is preferred for:
Correct answer: B. Flat pads suitable for fine-pitch components
44. Component placement should prioritise:
Correct answer: A. Critical parts like connectors, ICs and decoupling first
45. Decoupling capacitors should be placed:
Correct answer: C. As close as possible to IC power pins
46. Trace width depends on:
Correct answer: A. Required current, copper thickness and allowed temperature rise
47. IPC-2221 provides guidelines for:
Correct answer: B. Trace width, spacing and general PCB design
48. Clearance between traces must consider:
Correct answer: B. Voltage levels and manufacturing capability
49. Right-angle traces are often avoided because:
Correct answer: D. They can cause etching issues and are poor practice for high-speed signals
50. A ground plane provides:
Correct answer: D. A low-impedance return path and reduces noise
Questions 51 to 75
51. Splitting ground planes carelessly can:
Correct answer: C. Create long return paths and increase EMI
52. Return current for high-frequency signals flows:
Correct answer: A. Directly beneath the signal trace on the reference plane
53. Controlled impedance traces are required for:
Correct answer: B. High-speed signals like USB, HDMI and DDR
54. Common single-ended controlled impedance value is:
Correct answer: B. 50 ohms
55. Differential pairs must be routed:
Correct answer: D. Close together with matched lengths
56. USB differential pair impedance is typically:
Correct answer: D. 90 ohms differential
57. Length matching is important for:
Correct answer: D. Parallel buses and differential pairs to control skew
58. Signal integrity issues include:
Correct answer: C. Reflections, crosstalk and ringing
59. Crosstalk can be reduced by:
Correct answer: D. Increasing spacing and using ground planes between signals
60. Termination resistors help to:
Correct answer: A. Reduce reflections on transmission lines
61. Power integrity focuses on:
Correct answer: D. Delivering stable, low-noise power to all components
62. A power distribution network (PDN) includes:
Correct answer: C. Regulators, planes, traces and decoupling capacitors
63. Wide copper pours for power help to:
Correct answer: C. Reduce resistance and voltage drop
64. Thermal relief pads help to:
Correct answer: C. Make soldering easier on pads connected to large copper areas
65. Thermal vias under power components:
Correct answer: C. Conduct heat to other layers or heatsinks
66. Crystal oscillators should be placed:
Correct answer: D. Close to the IC with short traces and a ground guard
67. Analog and digital sections should be:
Correct answer: C. Separated to reduce noise coupling
68. Antenna keep-out areas require:
Correct answer: D. No copper or components near the antenna region
69. EMI can be reduced on PCBs by:
Correct answer: C. Short return paths, solid ground planes and filtering
70. ESD protection devices should be placed:
Correct answer: B. Near connectors where discharge enters
71. Fiducial marks help:
Correct answer: A. Pick-and-place machines align the board optically
72. Test points allow:
Correct answer: C. Probing signals during manufacturing and debugging
73. Panelisation means:
Correct answer: B. Combining multiple boards on one panel for efficient manufacturing
74. V-scoring and mouse bites are used for:
Correct answer: D. Separating boards from a panel
75. Gerber files contain:
Correct answer: B. Image data for each copper, mask and silkscreen layer
Questions 76 to 100
76. NC drill files specify:
Correct answer: D. Hole locations and sizes
77. A pick-and-place (centroid) file lists:
Correct answer: B. Component positions and rotations for assembly machines
78. A BOM should include:
Correct answer: C. Part numbers, values, quantities and reference designators
79. ODB++ and IPC-2581 are:
Correct answer: A. Intelligent data formats for PCB manufacturing
80. SMT stands for:
Correct answer: C. Surface-mount technology
81. Reflow soldering uses:
Correct answer: D. Solder paste and controlled heating profiles
82. Wave soldering is commonly used for:
Correct answer: C. Through-hole components
83. A solder paste stencil defines:
Correct answer: A. Where paste is applied on SMD pads
84. BGA packages require:
Correct answer: B. Careful fan-out routing and often X-ray inspection
85. Tombstoning is a defect where:
Correct answer: D. A small component lifts on one end during reflow
86. AOI (Automated Optical Inspection) checks:
Correct answer: B. Assembled boards for placement and soldering defects
87. DFM (Design for Manufacturing) ensures:
Correct answer: B. The design can be fabricated reliably at reasonable cost
88. DFA (Design for Assembly) focuses on:
Correct answer: B. Making components easy to place and solder
89. Flex PCBs are useful for:
Correct answer: C. Applications requiring bending or tight spaces
90. Rigid-flex boards combine:
Correct answer: A. Rigid sections connected by flexible circuits
91. Metal-core PCBs are used for:
Correct answer: C. High-power LEDs needing good heat dissipation
92. High-frequency RF boards often use:
Correct answer: D. Low-loss materials such as Rogers laminates
93. Popular PCB design tools include:
Correct answer: A. KiCad, Altium Designer, OrCAD and Eagle
94. KiCad is:
Correct answer: D. A free, open-source PCB design suite
95. 3D models in PCB tools help to:
Correct answer: D. Check mechanical fit with enclosures
96. Design reviews before fabrication help to:
Correct answer: A. Catch errors early and avoid costly respins
97. The main goal of good PCB design is:
Correct answer: D. A reliable, manufacturable board meeting electrical and mechanical requirements
98. Teardrops at pad-trace junctions help to:
Correct answer: A. Strengthen connections and reduce drilling breakout
99. Creepage distance is important for:
Correct answer: B. High-voltage isolation along the board surface
100. Mounting holes should be:
Correct answer: D. Placed with clearance from traces and components
How to Pass the PCB Design Exam
- Read every question carefully; most options look similar, so look for the most precise answer.
- Revise the questions above topic by topic rather than memorising letters, because option order can change in the live test.
- You need 80 correct answers out of 100 to pass, so aim to understand at least 85 to stay safe.
- If you do not clear it on the first attempt, review the questions you missed and use the retake option.
Frequently Asked Questions
How many questions are in the PCB Design Professional Certification exam?
The exam has 100 multiple-choice questions, each worth 1 mark.
What is the passing score for the PCB Design Professional Certification?
You need at least 80% (80 out of 100) to pass and receive the certificate.
Can I retake the PCB Design Professional Certification exam?
Yes. If you score below 80%, you can retry the test after reviewing the topics.
Is the Itronix certificate verifiable?
Yes. Every certificate issued by Itronix Solutions has a unique ID that can be checked on the Itronix verify-certificate page.
More Electronics & Hardware Certification Answers
- Computer Architecture and Organization Professional Certification Exam Answers
- Computer Hardware and Networking Professional Certification Exam Answers
- Embedded Linux Development Professional Certification Exam Answers
- Embedded Systems Design Professional Certification Exam Answers
- FPGA Design Professional Certification Exam Answers
- Hardware Security Professional Certification Exam Answers
- IOT – Internet of Things Certification Exam Answers
- IoT Hardware Development Professional Certification Exam Answers
Disclaimer: These answers are provided for learning and revision. Questions and answers are checked regularly; if you find a mistake, let us know in the comments.
Priya Dogra – Free Certifications, Exam Answers & Career Guides Free certification exam answers, courses, scholarships and career guides for learners worldwide