FPGA Design Professional Certification exam answers 2026: This page lists all 100 questions of the official FPGA Design Professional Certification exam by Itronix Solutions, each with its four answer options and the correct answer highlighted in green. Use it to revise every topic before you attempt the test and earn your verifiable certificate.
About this certification: This certification covers FPGA architecture, HDL programming, and digital signal processing. Learn to design high-speed circuits and optimize hardware performance using programmable logic.
| Certification | FPGA Design Professional Certification |
| Provider | Itronix Solutions |
| Category | Electronics & Hardware |
| Total questions | 100 multiple-choice questions |
| Marks | 1 mark per question (100 marks) |
| Passing score | 80% (80 out of 100) |
| Retake | Available if you do not pass |
| Certificate | Verifiable online certificate |
Take the exam: FPGA Design Professional Certification on Itronix Solutions. See every other Itronix exam in our complete list of Itronix certification answers.
FPGA Design Exam Questions and Answers
Questions 1 to 25
1. What does FPGA stand for?
Correct answer: B. B) Field Programmable Gate Array
2. What is the main advantage of using an FPGA over an ASIC (Application-Specific Integrated Circuit)?
Correct answer: C. C) Reprogrammability
3. Which hardware description language is commonly used for FPGA programming?
Correct answer: A. A) VHDL
4. What is the primary purpose of a Look-Up Table (LUT) in an FPGA?
Correct answer: A. A) To implement combinational logic
5. What is the function of a flip-flop in an FPGA?
Correct answer: B. B) To store a single bit of data
6. What is the role of the configuration memory in an FPGA?
Correct answer: B. B) To hold the programming data that defines the circuit behavior
7. What is the purpose of a clock signal in an FPGA?
Correct answer: C. C) To synchronize data transfer and processing
8. Which FPGA architecture allows partial reconfiguration while other parts continue operating?
Correct answer: B. B) Dynamic architecture
9. What is the primary function of the routing matrix in an FPGA?
Correct answer: C. C) To connect different logic blocks
10. Which component in an FPGA is responsible for storing state information in sequential circuits?
Correct answer: B. B) Flip-flop
11. What type of memory is typically used to store the FPGA configuration data?
Correct answer: B. B) Flash
12. What is the primary difference between a CPLD (Complex Programmable Logic Device) and an FPGA?
Correct answer: C. C) FPGAs are more complex and offer more flexibility than CPLDs
13. Which tool is commonly used to simulate FPGA designs?
Correct answer: A. A) ModelSim
14. What type of logic allows an FPGA to perform both combinational and sequential operations?
Correct answer: B. B) Synchronous logic
15. What is the role of a multiplexer in an FPGA?
Correct answer: C. C) To select between multiple input signals
16. What is the purpose of a JTAG interface in FPGA development?
Correct answer: A. A) To program and debug the FPGA
17. What is the benefit of using a soft processor core in an FPGA?
Correct answer: B. B) Increased flexibility and customizability
18. What type of gate is used to create a basic flip-flop in FPGA design?
Correct answer: A. A) NAND gate
19. What does RTL stand for in FPGA design?
Correct answer: B. B) Register Transfer Level
20. Which programming method allows configuring an FPGA at runtime without powering down the device?
Correct answer: B. B) Dynamic reconfiguration
21. An FPGA is:
Correct answer: A. A reconfigurable integrated circuit programmed after manufacturing
22. FPGA stands for:
Correct answer: A. Field-Programmable Gate Array
23. The basic logic element of most FPGAs is built around:
Correct answer: B. Look-up tables (LUTs) and flip-flops
24. A LUT implements logic by:
Correct answer: A. Storing the truth table of a function in small memory
25. Configurable Logic Blocks (CLBs) contain:
Correct answer: A. LUTs, flip-flops and carry logic
Questions 26 to 50
26. Programmable interconnect in an FPGA:
Correct answer: A. Routes signals between logic blocks
27. Block RAM (BRAM) in FPGAs provides:
Correct answer: B. On-chip dedicated memory blocks
28. DSP slices in FPGAs are optimised for:
Correct answer: D. Multiply-accumulate and arithmetic operations
29. I/O blocks (IOBs) handle:
Correct answer: B. Interfacing internal logic with external pins and standards
30. The configuration file loaded into an FPGA is called a:
Correct answer: D. Bitstream
31. Most SRAM-based FPGAs:
Correct answer: B. Lose configuration on power-off and reload from external memory
32. Flash-based and antifuse FPGAs offer:
Correct answer: C. Non-volatile configuration
33. FPGA versus ASIC: FPGAs offer:
Correct answer: B. Reprogrammability and faster time to market
34. ASICs are preferred when:
Correct answer: B. Volumes are very high and power or cost per unit must be minimal
35. Major FPGA vendors include:
Correct answer: D. AMD (Xilinx), Intel (Altera), Lattice and Microchip
36. Hardware description languages used for FPGAs are:
Correct answer: B. VHDL and Verilog/SystemVerilog
37. HDL code describes:
Correct answer: D. Hardware structure and behaviour that runs concurrently
38. In Verilog, a module is:
Correct answer: A. The basic building block describing a hardware component
39. In VHDL, the entity declares:
Correct answer: B. The interface (ports) of a design unit
40. In VHDL, the architecture describes:
Correct answer: B. The internal implementation of an entity
41. Combinational logic outputs depend on:
Correct answer: D. Current inputs only
42. Sequential logic outputs depend on:
Correct answer: B. Current inputs and stored state
43. In Verilog, always @(posedge clk) describes:
Correct answer: B. Logic triggered on the rising clock edge
44. Non-blocking assignment (<=) in Verilog is used for:
Correct answer: A. Sequential logic in clocked blocks
45. Blocking assignment (=) in Verilog is typically used for:
Correct answer: B. Combinational logic within always blocks
46. Incomplete if or case statements in combinational logic can infer:
Correct answer: D. Unwanted latches
47. A finite state machine (FSM) consists of:
Correct answer: B. States, transitions and outputs
48. Moore machine outputs depend on:
Correct answer: A. The current state only
49. Mealy machine outputs depend on:
Correct answer: D. Current state and inputs
50. One-hot state encoding uses:
Correct answer: B. One flip-flop per state with a single bit set
Questions 51 to 75
51. Synthesis converts:
Correct answer: B. HDL code into a gate-level netlist
52. Implementation (place and route) maps the netlist:
Correct answer: C. Onto physical FPGA resources and routes connections
53. AMD Xilinx’s FPGA design suite is:
Correct answer: A. Vivado
54. Intel’s FPGA design suite is:
Correct answer: B. Quartus Prime
55. Simulation verifies:
Correct answer: C. Design functionality before hardware implementation
56. A testbench is:
Correct answer: B. HDL code that applies stimulus and checks a design’s outputs
57. Popular HDL simulators include:
Correct answer: D. ModelSim/Questa, Vivado Simulator and Verilator
58. Waveform viewers display:
Correct answer: C. Signal values over simulation time
59. Static timing analysis (STA) checks:
Correct answer: B. Whether all paths meet timing without simulation vectors
60. Setup time is:
Correct answer: A. The time data must be stable before the clock edge
61. Hold time is:
Correct answer: A. The time data must remain stable after the clock edge
62. Negative slack in timing reports means:
Correct answer: D. A timing path fails to meet its requirement
63. The critical path is:
Correct answer: A. The longest delay path limiting maximum clock frequency
64. Pipelining improves throughput by:
Correct answer: A. Inserting registers to split long combinational paths
65. Timing constraints (e.g. XDC or SDC files) specify:
Correct answer: C. Clock periods, I/O delays and timing exceptions
66. Pin assignment constraints define:
Correct answer: D. Which FPGA pins connect to external signals
67. A clock domain crossing occurs when:
Correct answer: D. Signals pass between logic driven by different clocks
68. Metastability can occur when:
Correct answer: A. An asynchronous signal violates a flip-flop’s setup or hold time
69. A two-flip-flop synchroniser is used to:
Correct answer: D. Reduce metastability risk for single-bit CDC signals
70. Asynchronous FIFOs are used to:
Correct answer: D. Safely transfer multi-bit data between clock domains
71. Gray code counters are used in async FIFOs because:
Correct answer: D. Only one bit changes per increment
72. PLLs and MMCMs in FPGAs are used to:
Correct answer: A. Generate and adjust clock frequencies and phases
73. Global clock buffers distribute clocks:
Correct answer: D. With low skew across the device
74. Clock gating in FPGAs should generally be avoided in logic because:
Correct answer: D. It can cause glitches and timing problems; use clock enables instead
75. Synchronous resets are:
Correct answer: C. Sampled on the active clock edge
Questions 76 to 100
76. Resource utilisation reports show:
Correct answer: D. How many LUTs, FFs, BRAMs and DSPs a design uses
77. IP cores are:
Correct answer: C. Pre-verified reusable design blocks such as FIFOs or Ethernet MACs
78. AXI is:
Correct answer: C. An ARM AMBA on-chip bus protocol widely used in FPGA SoCs
79. AXI-Stream is used for:
Correct answer: D. Unidirectional high-throughput streaming data
80. SoC FPGAs such as Zynq combine:
Correct answer: C. Hard ARM processor cores with programmable logic
81. Soft processors such as MicroBlaze or Nios V are:
Correct answer: B. CPUs implemented in FPGA logic
82. High-Level Synthesis (HLS) allows:
Correct answer: C. Generating hardware from C/C++ descriptions
83. Partial reconfiguration lets designers:
Correct answer: A. Reprogram part of the FPGA while the rest keeps running
84. JTAG is used with FPGAs for:
Correct answer: A. Programming, boundary scan and debugging
85. Integrated Logic Analyzers (ILA/SignalTap) allow:
Correct answer: D. Capturing internal signals in real hardware
86. High-speed transceivers (SerDes) in FPGAs support:
Correct answer: B. Multi-gigabit serial protocols like PCIe and Ethernet
87. LVDS is:
Correct answer: D. A low-voltage differential signalling standard
88. DDR memory interfaces on FPGAs require:
Correct answer: A. Memory controllers and careful timing calibration
89. FPGAs are widely used in:
Correct answer: D. Telecom, signal processing, aerospace, data centres and prototyping
90. FPGA acceleration benefits workloads that are:
Correct answer: A. Highly parallel and require low latency
91. ASIC prototyping on FPGAs helps to:
Correct answer: D. Validate chip designs before costly fabrication
92. Power consumption in FPGAs includes:
Correct answer: D. Static leakage and dynamic switching power
93. Reducing toggle rates and using clock enables help to:
Correct answer: C. Lower dynamic power consumption
94. Floorplanning helps to:
Correct answer: D. Guide placement of logic to improve timing
95. Linting HDL code helps to:
Correct answer: C. Catch coding style issues and potential bugs early
96. Version control for HDL projects helps to:
Correct answer: A. Track changes and collaborate safely
97. Bitstream encryption protects:
Correct answer: C. Design IP from copying and tampering
98. The key advantage of FPGAs is:
Correct answer: A. Massively parallel, reconfigurable hardware customised for the task
99. Carry chains in FPGAs speed up:
Correct answer: C. Arithmetic operations such as addition and counters
100. Generics in VHDL and parameters in Verilog allow:
Correct answer: B. Configurable, reusable modules
How to Pass the FPGA Design Exam
- Read every question carefully; most options look similar, so look for the most precise answer.
- Revise the questions above topic by topic rather than memorising letters, because option order can change in the live test.
- You need 80 correct answers out of 100 to pass, so aim to understand at least 85 to stay safe.
- If you do not clear it on the first attempt, review the questions you missed and use the retake option.
Frequently Asked Questions
How many questions are in the FPGA Design Professional Certification exam?
The exam has 100 multiple-choice questions, each worth 1 mark.
What is the passing score for the FPGA Design Professional Certification?
You need at least 80% (80 out of 100) to pass and receive the certificate.
Can I retake the FPGA Design Professional Certification exam?
Yes. If you score below 80%, you can retry the test after reviewing the topics.
Is the Itronix certificate verifiable?
Yes. Every certificate issued by Itronix Solutions has a unique ID that can be checked on the Itronix verify-certificate page.
More Electronics & Hardware Certification Answers
- Computer Architecture and Organization Professional Certification Exam Answers
- Computer Hardware and Networking Professional Certification Exam Answers
- Embedded Linux Development Professional Certification Exam Answers
- Embedded Systems Design Professional Certification Exam Answers
- Hardware Security Professional Certification Exam Answers
- IOT – Internet of Things Certification Exam Answers
- IoT Hardware Development Professional Certification Exam Answers
- Microprocessor and Microcontroller Programming Professional Certification Exam Answers
Disclaimer: These answers are provided for learning and revision. Questions and answers are checked regularly; if you find a mistake, let us know in the comments.
Priya Dogra – Free Certifications, Exam Answers & Career Guides Free certification exam answers, courses, scholarships and career guides for learners worldwide