Wednesday , November 18 2026
Breaking News

Microprocessor and Microcontroller Programming Professional Certification Exam Answers 2026 (All 100 Questions)

Microprocessor and Microcontroller Programming Professional Certification exam answers 2026: This page lists all 100 questions of the official Microprocessor and Microcontroller Programming Professional Certification exam by Itronix Solutions, each with its four answer options and the correct answer highlighted in green. Use it to revise every topic before you attempt the test and earn your verifiable certificate.

About this certification: Learn to program microprocessors and microcontrollers with this certification. It covers architecture, instruction sets, and interfacing. Ideal for embedded developers, it helps you build efficient control systems.

Certification Microprocessor and Microcontroller Programming Professional Certification
Provider Itronix Solutions
Category Electronics & Hardware
Total questions 100 multiple-choice questions
Marks 1 mark per question (100 marks)
Passing score 80% (80 out of 100)
Retake Available if you do not pass
Certificate Verifiable online certificate

Take the exam: Microprocessor and Microcontroller Programming Professional Certification on Itronix Solutions. See every other Itronix exam in our complete list of Itronix certification answers.

Microprocessor and Microcontroller Programming Exam Questions and Answers

Questions 1 to 25

1. What is the primary difference between a microprocessor and a microcontroller?

A. A) A microprocessor includes memory and I/O ports
B. B) A microcontroller only processes data
C. C) A microcontroller has integrated memory and I/O ports, while a microprocessor does not ✔
D. D) A microcontroller is faster than a microprocessor

Correct answer: C. C) A microcontroller has integrated memory and I/O ports, while a microprocessor does not

2. Which register holds the address of the next instruction to be executed in a microprocessor?

A. A) Data Register
B. B) Program Counter (PC) ✔
C. C) Instruction Register
D. D) Stack Pointer

Correct answer: B. B) Program Counter (PC)

3. What is the main function of an ALU (Arithmetic Logic Unit) in a microprocessor?

A. A) To perform arithmetic and logical operations ✔
B. B) To store data
C. C) To fetch instructions
D. D) To control peripheral devices

Correct answer: A. A) To perform arithmetic and logical operations

4. Which microcontroller architecture allows both program and data memory to share the same address space?

A. A) Von Neumann Architecture ✔
B. B) Harvard Architecture
C. C) RISC Architecture
D. D) CISC Architecture

Correct answer: A. A) Von Neumann Architecture

5. What is the purpose of the clock signal in a microcontroller?

A. A) To store data
B. B) To fetch instructions
C. C) To perform calculations
D. D) To synchronize internal operations ✔

Correct answer: D. D) To synchronize internal operations

6. What does RISC stand for in processor design?

A. A) Real Instruction Set Compiler
B. B) Reduced Instruction Set Computer ✔
C. C) Reversible Instruction Set Compiler
D. D) Random Instruction Set Computer

Correct answer: B. B) Reduced Instruction Set Computer

7. What is the purpose of an interrupt in a microprocessor-based system?

A. A) To execute the next instruction
B. B) To handle events requiring immediate attention ✔
C. C) To control program flow
D. D) To store data temporarily

Correct answer: B. B) To handle events requiring immediate attention

8. Which type of memory in a microcontroller is used for permanent storage of program code?

A. A) RAM
B. B) ROM ✔
C. C) Cache
D. D) Registers

Correct answer: B. B) ROM

9. What is the width of the data bus in an 8-bit microcontroller?

A. A) 4 bits
B. B) 8 bits ✔
C. C) 16 bits
D. D) 32 bits

Correct answer: B. B) 8 bits

10. Which instruction is used to transfer data from one register to another in an 8051 microcontroller?

A. A) MOVX
B. B) INC
C. C) MOV ✔
D. D) ADD

Correct answer: C. C) MOV

11. What is the function of the stack pointer in a microcontroller?

A. A) To store data temporarily
B. B) To keep track of the top of the stack ✔
C. C) To execute instructions
D. D) To decode instructions

Correct answer: B. B) To keep track of the top of the stack

12. What is the primary purpose of the watchdog timer in a microcontroller?

A. A) To reset the system if it becomes unresponsive ✔
B. B) To generate a clock signal
C. C) To amplify signals
D. D) To store data

Correct answer: A. A) To reset the system if it becomes unresponsive

13. Which type of addressing mode uses the direct address of the data in the instruction?

A. A) Immediate Addressing
B. B) Direct Addressing ✔
C. C) Indirect Addressing
D. D) Indexed Addressing

Correct answer: B. B) Direct Addressing

14. What is the purpose of the accumulator register in a microprocessor?

A. A) To store program codes
B. B) To hold intermediate results of calculations ✔
C. C) To store the program counter value
D. D) To control the clock signal

Correct answer: B. B) To hold intermediate results of calculations

15. What is the size of the instruction register in an 8-bit microcontroller?

A. A) 8 bits ✔
B. B) 16 bits
C. C) 32 bits
D. D) 64 bits

Correct answer: A. A) 8 bits

16. What type of memory is used to store data that can change during the execution of a program?

A. A) ROM
B. B) Flash
C. C) RAM ✔
D. D) EEPROM

Correct answer: C. C) RAM

17. In a microprocessor, which component is responsible for fetching, decoding, and executing instructions?

A. A) ALU
B. B) Control Unit ✔
C. C) Register
D. D) Program Counter

Correct answer: B. B) Control Unit

18. What is the function of a timer in a microcontroller?

A. A) To store program codes
B. B) To control power consumption
C. C) To generate time delays or measure time intervals ✔
D. D) To handle interrupts

Correct answer: C. C) To generate time delays or measure time intervals

19. Which communication protocol is often used for short-distance communication between microcontrollers and peripherals?

A. A) I2C ✔
B. B) HTTP
C. C) UDP
D. D) FTP

Correct answer: A. A) I2C

20. What is the primary advantage of using a Harvard architecture in microcontrollers?

A. A) Simple design
B. B) Lower cost
C. C) Faster data access due to separate data and program memory buses ✔
D. D) Reduced complexity

Correct answer: C. C) Faster data access due to separate data and program memory buses

21. A microprocessor is:

A. A CPU on a single chip that needs external memory and peripherals ✔
B. A battery
C. A sensor
D. A complete computer with built-in peripherals always

Correct answer: A. A CPU on a single chip that needs external memory and peripherals

22. A microcontroller is:

A. A chip combining CPU, memory and I/O peripherals for embedded control ✔
B. Only memory
C. Only a CPU
D. A display

Correct answer: A. A chip combining CPU, memory and I/O peripherals for embedded control

23. The Intel 8085 is:

A. An 8-bit microprocessor ✔
B. A GPU
C. A sensor
D. A 32-bit microcontroller

Correct answer: A. An 8-bit microprocessor

24. The Intel 8086 is:

A. A memory chip
B. A 64-bit CPU
C. A 16-bit microprocessor ✔
D. An 8-bit microcontroller

Correct answer: C. A 16-bit microprocessor

25. The 8051 is:

A. A GPU
B. An FPGA
C. An 8-bit microcontroller family ✔
D. A 16-bit microprocessor

Correct answer: C. An 8-bit microcontroller family

Questions 26 to 50

26. ARM Cortex-M processors are commonly used in:

A. Hard drives
B. Mainframes only
C. Microcontrollers for embedded systems ✔
D. Graphics cards

Correct answer: C. Microcontrollers for embedded systems

27. The address bus carries:

A. Power
B. Data values only
C. Memory or I/O addresses from the CPU ✔
D. Control signals only

Correct answer: C. Memory or I/O addresses from the CPU

28. The data bus carries:

A. Only power
B. Data between CPU, memory and peripherals ✔
C. Only addresses
D. Only clocks

Correct answer: B. Data between CPU, memory and peripherals

29. The control bus carries:

A. Only addresses
B. Signals like read, write and interrupt ✔
C. Only power
D. Only data

Correct answer: B. Signals like read, write and interrupt

30. A 16-bit address bus can address:

A. 4 GB
B. 1 MB
C. 16 KB
D. 64 KB of memory ✔

Correct answer: D. 64 KB of memory

31. A 20-bit address bus (as in 8086) can address:

A. 64 KB
B. 16 MB
C. 4 GB
D. 1 MB of memory ✔

Correct answer: D. 1 MB of memory

32. The program counter (PC) holds:

A. The address of the next instruction ✔
B. The stack top
C. The current data value
D. The flags

Correct answer: A. The address of the next instruction

33. The stack pointer (SP) points to:

A. The top of the stack in memory ✔
B. The accumulator
C. The next instruction
D. The data bus

Correct answer: A. The top of the stack in memory

34. The accumulator is:

A. A clock
B. A memory chip
C. A register used for arithmetic and logic results ✔
D. A bus

Correct answer: C. A register used for arithmetic and logic results

35. The flag register stores:

A. Data only
B. Memory addresses
C. Status bits like zero, carry and sign ✔
D. Program instructions

Correct answer: C. Status bits like zero, carry and sign

36. The carry flag is set when:

A. An interrupt occurs
B. An arithmetic operation produces a carry or borrow ✔
C. The result is zero
D. The result is negative

Correct answer: B. An arithmetic operation produces a carry or borrow

37. The zero flag is set when:

A. There is a carry
B. Overflow occurs
C. The result of an operation is zero ✔
D. The result is negative

Correct answer: C. The result of an operation is zero

38. The instruction cycle consists of:

A. Read, write and erase
B. Start and stop
C. Fetch, decode and execute ✔
D. Input and output only

Correct answer: C. Fetch, decode and execute

39. Opcode is:

A. The memory address
B. The clock speed
C. The data value
D. The part of an instruction specifying the operation ✔

Correct answer: D. The part of an instruction specifying the operation

40. Immediate addressing mode uses:

A. A constant value within the instruction ✔
B. An I/O port
C. A register only
D. A memory address

Correct answer: A. A constant value within the instruction

41. Direct addressing mode uses:

A. A constant
B. The stack only
C. A register pointer
D. The memory address specified in the instruction ✔

Correct answer: D. The memory address specified in the instruction

42. Register indirect addressing uses:

A. A register that holds the memory address ✔
B. The program counter
C. A constant
D. A port number

Correct answer: A. A register that holds the memory address

43. Assembly language is:

A. A high-level language like Python
B. A database query language
C. A markup language
D. A low-level language with mnemonics mapping to machine instructions ✔

Correct answer: D. A low-level language with mnemonics mapping to machine instructions

44. An assembler converts:

A. Machine code into assembly only
B. Assembly code into machine code ✔
C. C into Python
D. HTML into code

Correct answer: B. Assembly code into machine code

45. MOV instruction typically:

A. Jumps to an address
B. Adds numbers
C. Stops the CPU
D. Copies data from source to destination ✔

Correct answer: D. Copies data from source to destination

46. ADD instruction:

A. Compares values
B. Adds two operands ✔
C. Moves data
D. Halts execution

Correct answer: B. Adds two operands

47. JMP instruction:

A. Adds values
B. Moves data
C. Transfers control to another address ✔
D. Pushes to stack

Correct answer: C. Transfers control to another address

48. CALL instruction:

A. Clears memory
B. Adds numbers
C. Ends the program
D. Calls a subroutine and saves the return address ✔

Correct answer: D. Calls a subroutine and saves the return address

49. RET instruction:

A. Moves data
B. Returns from a subroutine ✔
C. Resets the CPU
D. Calls a subroutine

Correct answer: B. Returns from a subroutine

50. PUSH and POP instructions:

A. Store and retrieve data on the stack ✔
B. Read ports
C. Add and subtract
D. Set flags only

Correct answer: A. Store and retrieve data on the stack

Questions 51 to 75

51. An interrupt is:

A. A memory chip
B. A program bug
C. A bus type
D. A signal that temporarily diverts the CPU to handle an event ✔

Correct answer: D. A signal that temporarily diverts the CPU to handle an event

52. An ISR (Interrupt Service Routine) is:

A. A sensor
B. A memory type
C. The code executed in response to an interrupt ✔
D. A register

Correct answer: C. The code executed in response to an interrupt

53. Maskable interrupts can be:

A. Never disabled
B. Enabled or disabled by software ✔
C. Only hardware reset
D. Ignored always

Correct answer: B. Enabled or disabled by software

54. Non-maskable interrupts (NMI) are:

A. High-priority interrupts that cannot be disabled by software ✔
B. Software only
C. Low priority
D. Always ignored

Correct answer: A. High-priority interrupts that cannot be disabled by software

55. Interrupt vector table holds:

A. Addresses of interrupt service routines ✔
B. Flags only
C. Data values
D. Program text

Correct answer: A. Addresses of interrupt service routines

56. Polling differs from interrupts because it:

A. Repeatedly checks device status in a loop ✔
B. Responds automatically to events
C. Uses no CPU
D. Is hardware only

Correct answer: A. Repeatedly checks device status in a loop

57. ROM is:

A. A register
B. Volatile working memory
C. A cache only
D. Non-volatile memory used to store firmware ✔

Correct answer: D. Non-volatile memory used to store firmware

58. RAM is:

A. A CPU register
B. An I/O device
C. Permanent storage
D. Volatile memory for temporary data ✔

Correct answer: D. Volatile memory for temporary data

59. Flash memory in microcontrollers stores:

A. Only cache
B. Only temporary variables
C. Only stack
D. Program code that remains after power loss ✔

Correct answer: D. Program code that remains after power loss

60. EEPROM is used to store:

A. Cache
B. Program execution stack
C. Small non-volatile data like configuration settings ✔
D. Video frames

Correct answer: C. Small non-volatile data like configuration settings

61. Harvard architecture has:

A. No memory
B. A single shared memory
C. Separate memory and buses for instructions and data ✔
D. Only cache

Correct answer: C. Separate memory and buses for instructions and data

62. Von Neumann architecture has:

A. A shared memory for instructions and data ✔
B. Separate memories
C. Only registers
D. No buses

Correct answer: A. A shared memory for instructions and data

63. RISC processors use:

A. Many complex instructions
B. No instructions
C. A small set of simple instructions ✔
D. Only microcode

Correct answer: C. A small set of simple instructions

64. CISC processors use:

A. No memory
B. A large set of complex instructions ✔
C. No registers
D. Only simple instructions

Correct answer: B. A large set of complex instructions

65. Pipelining improves:

A. Instruction throughput by overlapping execution stages ✔
B. Clock accuracy
C. Memory size
D. Power usage always

Correct answer: A. Instruction throughput by overlapping execution stages

66. Clock speed is measured in:

A. Hertz (MHz or GHz) ✔
B. Volts
C. Ohms
D. Bytes

Correct answer: A. Hertz (MHz or GHz)

67. A crystal oscillator provides:

A. Power
B. Display
C. Storage
D. A stable clock signal ✔

Correct answer: D. A stable clock signal

68. GPIO pins can be configured as:

A. Digital inputs or outputs ✔
B. Only memory
C. Only clock pins
D. Only power pins

Correct answer: A. Digital inputs or outputs

69. Pull-up resistors ensure:

A. Always low inputs
B. Faster clocks
C. A defined logic high when an input is not driven ✔
D. More current

Correct answer: C. A defined logic high when an input is not driven

70. Timers/counters in microcontrollers are used for:

A. Storing programs
B. Wi-Fi
C. Delays, measuring time and generating PWM ✔
D. Displays only

Correct answer: C. Delays, measuring time and generating PWM

71. PWM can control:

A. Address bus width
B. Motor speed and LED brightness ✔
C. Memory size
D. Clock source

Correct answer: B. Motor speed and LED brightness

72. An ADC converts:

A. Analogue voltages into digital values ✔
B. Light to sound
C. Digital to analogue
D. Power to data

Correct answer: A. Analogue voltages into digital values

73. ADC resolution of 12 bits provides:

A. 12 levels
B. 256 levels
C. 1024 levels
D. 4096 levels ✔

Correct answer: D. 4096 levels

74. A DAC converts:

A. Analogue to digital
B. Digital values into analogue voltages ✔
C. AC to DC
D. Sound to light

Correct answer: B. Digital values into analogue voltages

75. UART communication is:

A. Asynchronous serial using TX and RX ✔
B. Wireless only
C. Parallel only
D. Synchronous with a clock

Correct answer: A. Asynchronous serial using TX and RX

Questions 76 to 100

76. Baud rate in UART specifies:

A. Clock source
B. Memory size
C. Voltage level
D. Symbols (bits) transmitted per second ✔

Correct answer: D. Symbols (bits) transmitted per second

77. I2C uses:

A. Two wires: SDA (data) and SCL (clock) with addressing ✔
B. Wireless signals
C. One wire only
D. Four wires always

Correct answer: A. Two wires: SDA (data) and SCL (clock) with addressing

78. SPI uses:

A. Radio only
B. MOSI, MISO, SCLK and chip select lines ✔
C. One wire
D. Only two wires

Correct answer: B. MOSI, MISO, SCLK and chip select lines

79. SPI is generally faster than I2C because:

A. It uses fewer wires
B. It is wireless
C. It has addressing overhead
D. It is full-duplex with a dedicated clock and simpler protocol ✔

Correct answer: D. It is full-duplex with a dedicated clock and simpler protocol

80. CAN bus is widely used in:

A. Audio jacks
B. Automotive and industrial networks ✔
C. Displays only
D. Home Wi-Fi

Correct answer: B. Automotive and industrial networks

81. A watchdog timer resets the system when:

A. Power is normal
B. Software fails to refresh it in time ✔
C. An interrupt is handled
D. A key is pressed

Correct answer: B. Software fails to refresh it in time

82. Brown-out detection resets the MCU when:

A. Memory is full
B. Clock is fast
C. Voltage is normal
D. Supply voltage drops below a safe level ✔

Correct answer: D. Supply voltage drops below a safe level

83. Low-power modes in microcontrollers reduce:

A. Pin count
B. Energy consumption during idle times ✔
C. Memory size
D. Clock accuracy only

Correct answer: B. Energy consumption during idle times

84. Bit masking is used to:

A. Compress files
B. Set, clear or test specific bits in registers ✔
C. Display text
D. Encrypt data

Correct answer: B. Set, clear or test specific bits in registers

85. Setting bit 3 of a register in C is done with:

A. reg = reg AND 3
B. reg = 3
C. reg = reg OR (1 shifted left by 3) ✔
D. reg = 0

Correct answer: C. reg = reg OR (1 shifted left by 3)

86. Memory-mapped I/O means:

A. No I/O exists
B. I/O uses separate instructions only
C. Peripheral registers are accessed via memory addresses ✔
D. Only files are used

Correct answer: C. Peripheral registers are accessed via memory addresses

87. Embedded C programs typically run:

A. Only on servers
B. In an infinite main loop ✔
C. Only in browsers
D. Once and exit

Correct answer: B. In an infinite main loop

88. The volatile keyword is used for variables that:

A. Are constants
B. Can change outside normal program flow, like hardware registers ✔
C. Are local only
D. Never change

Correct answer: B. Can change outside normal program flow, like hardware registers

89. Arduino Uno uses the:

A. ARM Cortex-A72
B. ATmega328P microcontroller ✔
C. ESP32
D. 8086

Correct answer: B. ATmega328P microcontroller

90. STM32 microcontrollers are based on:

A. ARM Cortex-M cores ✔
B. 8051 cores
C. x86 cores
D. PIC16 cores

Correct answer: A. ARM Cortex-M cores

91. PIC microcontrollers are made by:

A. Qualcomm
B. Microchip Technology ✔
C. Intel
D. AMD

Correct answer: B. Microchip Technology

92. Debugging microcontrollers is often done using:

A. HDMI
B. Audio jacks
C. Ethernet only
D. JTAG or SWD interfaces ✔

Correct answer: D. JTAG or SWD interfaces

93. An IDE such as STM32CubeIDE or MPLAB X is used to:

A. Write, compile and debug embedded code ✔
B. Design websites
C. Edit photos
D. Write documents

Correct answer: A. Write, compile and debug embedded code

94. Microcontrollers are preferred over microprocessors for:

A. Low-cost, low-power dedicated control tasks ✔
B. Heavy graphics
C. Large databases
D. Running desktop operating systems

Correct answer: A. Low-cost, low-power dedicated control tasks

95. The main role of microprocessors and microcontrollers is to:

A. Execute instructions to process data and control devices ✔
B. Supply power
C. Store all data permanently
D. Display only

Correct answer: A. Execute instructions to process data and control devices

96. HLT instruction in 8085:

A. Adds numbers
B. Calls a subroutine
C. Halts the processor ✔
D. Moves data

Correct answer: C. Halts the processor

97. The 8086 uses segment registers such as:

A. PC only
B. CS, DS, SS and ES ✔
C. SP only
D. AX only

Correct answer: B. CS, DS, SS and ES

98. The physical address in 8086 is calculated as:

A. Segment x 16 + offset ✔
B. Offset x 16
C. Segment x offset
D. Segment + offset only

Correct answer: A. Segment x 16 + offset

99. Little-endian systems store:

A. The least significant byte at the lowest address ✔
B. Only words
C. Only bits
D. The most significant byte first

Correct answer: A. The least significant byte at the lowest address

100. DMA allows:

A. Faster clocks
B. More interrupts
C. CPU to skip memory
D. Peripherals to transfer data to memory without CPU involvement ✔

Correct answer: D. Peripherals to transfer data to memory without CPU involvement

How to Pass the Microprocessor and Microcontroller Programming Exam

  • Read every question carefully; most options look similar, so look for the most precise answer.
  • Revise the questions above topic by topic rather than memorising letters, because option order can change in the live test.
  • You need 80 correct answers out of 100 to pass, so aim to understand at least 85 to stay safe.
  • If you do not clear it on the first attempt, review the questions you missed and use the retake option.

Frequently Asked Questions

How many questions are in the Microprocessor and Microcontroller Programming Professional Certification exam?

The exam has 100 multiple-choice questions, each worth 1 mark.

What is the passing score for the Microprocessor and Microcontroller Programming Professional Certification?

You need at least 80% (80 out of 100) to pass and receive the certificate.

Can I retake the Microprocessor and Microcontroller Programming Professional Certification exam?

Yes. If you score below 80%, you can retry the test after reviewing the topics.

Is the Itronix certificate verifiable?

Yes. Every certificate issued by Itronix Solutions has a unique ID that can be checked on the Itronix verify-certificate page.

More Electronics & Hardware Certification Answers

Disclaimer: These answers are provided for learning and revision. Questions and answers are checked regularly; if you find a mistake, let us know in the comments.

About Priya Dogra

Priya Dogra runs priyadogra.com, where she shares free certification courses, internships, jobs, scholarships and exam preparation guides for Indian students and freshers. Follow her on YouTube, LinkedIn and Instagram for the latest opportunities.

Check Also

Unix/ Linux Certification exam answers 2026

Unix/ Linux Certification Exam Answers 2026 (All 100 Questions)

All 100 Unix/ Linux Certification exam questions with correct answers highlighted - updated 2026.

Leave a Reply

Your email address will not be published. Required fields are marked *