Wednesday , November 18 2026
Breaking News

PCB Design Professional Certification Exam Answers 2026 (All 100 Questions)

PCB Design Professional Certification exam answers 2026: This page lists all 100 questions of the official PCB Design Professional Certification exam by Itronix Solutions, each with its four answer options and the correct answer highlighted in green. Use it to revise every topic before you attempt the test and earn your verifiable certificate.

About this certification: Learn to design printed circuit boards (PCBs) with this certification. It covers PCB layout, signal integrity, and manufacturing processes. Gain expertise in schematic design, component placement, and testing.

Certification PCB Design Professional Certification
Provider Itronix Solutions
Category Electronics & Hardware
Total questions 100 multiple-choice questions
Marks 1 mark per question (100 marks)
Passing score 80% (80 out of 100)
Retake Available if you do not pass
Certificate Verifiable online certificate

Take the exam: PCB Design Professional Certification on Itronix Solutions. See every other Itronix exam in our complete list of Itronix certification answers.

PCB Design Exam Questions and Answers

Questions 1 to 25

1. What does PCB stand for?

A. A) Printed Circuit Board ✔
B. B) Process Control Board
C. C) Power Control Board
D. D) Peripheral Control Board

Correct answer: A. A) Printed Circuit Board

2. Which material is most commonly used as the base for a PCB?

A. A) Copper
B. B) Aluminum
C. C) FR4 (Fiberglass Reinforced Epoxy) ✔
D. D) Plastic

Correct answer: C. C) FR4 (Fiberglass Reinforced Epoxy)

3. What is the purpose of vias in a PCB?

A. A) To connect components to the power supply
B. B) To provide insulation
C. C) To create electrical connections between different layers of the PCB ✔
D. D) To enhance mechanical strength

Correct answer: C. C) To create electrical connections between different layers of the PCB

4. What is the primary function of a solder mask on a PCB?

A. A) To insulate the board
B. B) To protect the copper traces from oxidation and short circuits ✔
C. C) To provide a mounting surface
D. D) To improve signal strength

Correct answer: B. B) To protect the copper traces from oxidation and short circuits

5. What type of PCB is used when high flexibility is required?

A. A) Rigid PCB
B. B) Flexible PCB ✔
C. C) Multi-layer PCB
D. D) Single-layer PCB

Correct answer: B. B) Flexible PCB

6. What is the standard copper thickness for most PCBs?

A. A) 1 oz/ft² ✔
B. B) 0.5 oz/ft²
C. C) 2 oz/ft²
D. D) 4 oz/ft²

Correct answer: A. A) 1 oz/ft²

7. What is the primary purpose of a ground plane in a PCB?

A. A) To reduce electrical noise and provide a return path for signals ✔
B. B) To connect components
C. C) To increase the signal speed
D. D) To provide power to the components

Correct answer: A. A) To reduce electrical noise and provide a return path for signals

8. What is the function of a silkscreen layer on a PCB?

A. A) To provide component labels and markings ✔
B. B) To create electrical connections
C. C) To protect the copper traces
D. D) To improve conductivity

Correct answer: A. A) To provide component labels and markings

9. What does SMT stand for in PCB design?

A. A) Standard Mounting Technology
B. B) Single Mount Technology
C. C) Solder Mask Technology
D. D) Surface Mount Technology ✔

Correct answer: D. D) Surface Mount Technology

10. What is the primary advantage of using a multi-layer PCB?

A. A) Increased flexibility
B. B) Lower production cost
C. C) Higher component density and reduced noise ✔
D. D) Reduced manufacturing time

Correct answer: C. C) Higher component density and reduced noise

11. What type of PCB defect is caused by improper soldering?

A. A) Short Circuit
B. B) Open Circuit
C. C) Cold Joint ✔
D. D) Broken Trace

Correct answer: C. C) Cold Joint

12. What does the term "trace width" refer to in PCB design?

A. A) The thickness of the copper layer
B. B) The distance between components
C. C) The width of the copper conductor ✔
D. D) The size of the board

Correct answer: C. C) The width of the copper conductor

13. What is the primary reason for using a solder paste in SMT assembly?

A. A) To provide mechanical strength
B. B) To prevent corrosion
C. C) To protect copper traces
D. D) To create electrical and mechanical connections during reflow soldering ✔

Correct answer: D. D) To create electrical and mechanical connections during reflow soldering

14. What is the purpose of a decoupling capacitor in a PCB design?

A. A) To increase signal strength
B. B) To filter noise and stabilize the power supply ✔
C. C) To connect ground and power
D. D) To reduce current flow

Correct answer: B. B) To filter noise and stabilize the power supply

15. What is the function of a thermal relief in a PCB?

A. A) To increase signal strength
B. B) To reduce the board’s weight
C. C) To facilitate better heat dissipation ✔
D. D) To improve signal speed

Correct answer: C. C) To facilitate better heat dissipation

16. Which software is widely used for PCB design?

A. A) MATLAB
B. B) Altium Designer ✔
C. C) Python
D. D) SolidWorks

Correct answer: B. B) Altium Designer

17. What does a "netlist" represent in PCB design?

A. A) The list of board layers
B. B) The mechanical design
C. C) The component placement
D. D) The electrical connections between components ✔

Correct answer: D. D) The electrical connections between components

18. What is the purpose of a via fill in high-frequency PCBs?

A. A) To increase current flow
B. B) To reduce the weight of the PCB
C. C) To improve component alignment
D. D) To improve signal integrity and heat dissipation ✔

Correct answer: D. D) To improve signal integrity and heat dissipation

19. What type of PCB is commonly used in high-power applications?

A. A) Single-layer PCB
B. B) Metal Core PCB ✔
C. C) Flexible PCB
D. D) Plastic PCB

Correct answer: B. B) Metal Core PCB

20. What is the function of an impedance-controlled trace in a high-frequency PCB?

A. A) To increase current flow
B. B) To reduce the weight of the PCB
C. C) To maintain consistent signal integrity ✔
D. D) To increase the signal speed

Correct answer: C. C) To maintain consistent signal integrity

21. A printed circuit board (PCB) is:

A. A display
B. A software program
C. A board that mechanically supports and electrically connects components with copper traces ✔
D. A battery

Correct answer: C. A board that mechanically supports and electrically connects components with copper traces

22. The PCB design workflow typically starts with:

A. Assembly
B. Schematic capture ✔
C. Testing
D. Gerber generation

Correct answer: B. Schematic capture

23. A schematic symbol represents:

A. Its price
B. Its physical size
C. A component’s electrical connections ✔
D. Its colour

Correct answer: C. A component’s electrical connections

24. A footprint (land pattern) defines:

A. The firmware
B. The BOM price
C. The schematic symbol
D. The copper pads and outline for mounting a component on the PCB ✔

Correct answer: D. The copper pads and outline for mounting a component on the PCB

25. A netlist describes:

A. Firmware logic
B. The board colour
C. Component prices
D. Which component pins are connected together ✔

Correct answer: D. Which component pins are connected together

Questions 26 to 50

26. Electrical Rule Check (ERC) in a schematic detects:

A. Trace width errors
B. Unconnected pins and conflicting outputs ✔
C. Drill sizes
D. Silkscreen overlaps

Correct answer: B. Unconnected pins and conflicting outputs

27. Design Rule Check (DRC) in a layout detects:

A. Spacing, width and clearance violations ✔
B. Firmware bugs
C. Missing schematic symbols
D. Pricing errors

Correct answer: A. Spacing, width and clearance violations

28. FR-4 is:

A. A copper alloy
B. The most common glass-reinforced epoxy PCB substrate ✔
C. A component
D. A solder type

Correct answer: B. The most common glass-reinforced epoxy PCB substrate

29. Standard PCB thickness is commonly:

A. 1.6 mm ✔
B. 16 mm
C. 10 cm
D. 0.01 mm

Correct answer: A. 1.6 mm

30. Copper thickness is often specified in:

A. Hertz
B. Volts
C. Grams per litre
D. Ounces per square foot, e.g. 1 oz ✔

Correct answer: D. Ounces per square foot, e.g. 1 oz

31. A two-layer PCB has:

A. Copper on top and bottom layers ✔
B. No copper
C. Four copper layers
D. Only one copper layer

Correct answer: A. Copper on top and bottom layers

32. Multilayer PCBs allow:

A. Fewer connections
B. Dedicated power and ground planes and denser routing ✔
C. No vias
D. Only single-sided routing

Correct answer: B. Dedicated power and ground planes and denser routing

33. A typical four-layer stackup is:

A. Ground only
B. Signal, ground, power, signal ✔
C. Signal, signal, signal, signal always
D. Power only

Correct answer: B. Signal, ground, power, signal

34. A via is:

A. A component
B. A label
C. A plated hole connecting traces on different layers ✔
D. A test point only

Correct answer: C. A plated hole connecting traces on different layers

35. Through-hole vias go:

A. Only on the surface
B. Nowhere
C. Only between inner layers
D. Through all layers of the board ✔

Correct answer: D. Through all layers of the board

36. Blind vias connect:

A. An outer layer to one or more inner layers without passing through ✔
B. All layers
C. Two outer layers only
D. No layers

Correct answer: A. An outer layer to one or more inner layers without passing through

37. Buried vias connect:

A. Components
B. Inner layers only, not visible from outside ✔
C. Outer layers only
D. All layers

Correct answer: B. Inner layers only, not visible from outside

38. Microvias are used in:

A. Cables
B. High-density interconnect (HDI) boards ✔
C. Single-layer boards only
D. Breadboards

Correct answer: B. High-density interconnect (HDI) boards

39. Solder mask is:

A. A copper layer
B. A component
C. A protective coating that prevents solder bridges and oxidation ✔
D. A drill file

Correct answer: C. A protective coating that prevents solder bridges and oxidation

40. Silkscreen is used for:

A. Routing signals
B. Printing reference designators, labels and logos ✔
C. Conducting current
D. Protecting copper

Correct answer: B. Printing reference designators, labels and logos

41. Reference designators such as R1, C5 and U3 identify:

A. Layers
B. Individual components on the board ✔
C. Nets
D. Vias

Correct answer: B. Individual components on the board

42. Surface finishes such as HASL, ENIG and OSP:

A. Conduct heat only
B. Print labels
C. Protect exposed copper pads and aid soldering ✔
D. Add layers

Correct answer: C. Protect exposed copper pads and aid soldering

43. ENIG finish is preferred for:

A. Through-hole only
B. Flat pads suitable for fine-pitch components ✔
C. Lowest cost always
D. Silkscreen

Correct answer: B. Flat pads suitable for fine-pitch components

44. Component placement should prioritise:

A. Critical parts like connectors, ICs and decoupling first ✔
B. Labels first
C. Random placement
D. Mounting holes last always

Correct answer: A. Critical parts like connectors, ICs and decoupling first

45. Decoupling capacitors should be placed:

A. Far from ICs
B. Anywhere
C. As close as possible to IC power pins ✔
D. On a separate board

Correct answer: C. As close as possible to IC power pins

46. Trace width depends on:

A. Required current, copper thickness and allowed temperature rise ✔
B. Silkscreen
C. Board colour
D. Component count

Correct answer: A. Required current, copper thickness and allowed temperature rise

47. IPC-2221 provides guidelines for:

A. Marketing
B. Trace width, spacing and general PCB design ✔
C. Accounting
D. Software testing

Correct answer: B. Trace width, spacing and general PCB design

48. Clearance between traces must consider:

A. Labels only
B. Voltage levels and manufacturing capability ✔
C. Colour only
D. Price only

Correct answer: B. Voltage levels and manufacturing capability

49. Right-angle traces are often avoided because:

A. They look too neat
B. They use more copper always
C. They are illegal
D. They can cause etching issues and are poor practice for high-speed signals ✔

Correct answer: D. They can cause etching issues and are poor practice for high-speed signals

50. A ground plane provides:

A. Higher resistance
B. Extra signals
C. More EMI
D. A low-impedance return path and reduces noise ✔

Correct answer: D. A low-impedance return path and reduces noise

Questions 51 to 75

51. Splitting ground planes carelessly can:

A. Have no effect
B. Improve signal integrity always
C. Create long return paths and increase EMI ✔
D. Reduce noise always

Correct answer: C. Create long return paths and increase EMI

52. Return current for high-frequency signals flows:

A. Directly beneath the signal trace on the reference plane ✔
B. Only through components
C. Randomly across the board
D. Only through vias

Correct answer: A. Directly beneath the signal trace on the reference plane

53. Controlled impedance traces are required for:

A. DC power only
B. High-speed signals like USB, HDMI and DDR ✔
C. Mechanical holes
D. LED indicators

Correct answer: B. High-speed signals like USB, HDMI and DDR

54. Common single-ended controlled impedance value is:

A. 1 kilohm
B. 50 ohms ✔
C. 500 ohms
D. 5 ohms

Correct answer: B. 50 ohms

55. Differential pairs must be routed:

A. Far apart
B. With random lengths
C. On different boards
D. Close together with matched lengths ✔

Correct answer: D. Close together with matched lengths

56. USB differential pair impedance is typically:

A. 300 ohms
B. 1 ohm
C. 10 ohms
D. 90 ohms differential ✔

Correct answer: D. 90 ohms differential

57. Length matching is important for:

A. Power traces
B. Mounting holes
C. Silkscreen
D. Parallel buses and differential pairs to control skew ✔

Correct answer: D. Parallel buses and differential pairs to control skew

58. Signal integrity issues include:

A. Hole count
B. Label size
C. Reflections, crosstalk and ringing ✔
D. Board colour

Correct answer: C. Reflections, crosstalk and ringing

59. Crosstalk can be reduced by:

A. Routing traces closer
B. Removing ground
C. Longer parallel runs
D. Increasing spacing and using ground planes between signals ✔

Correct answer: D. Increasing spacing and using ground planes between signals

60. Termination resistors help to:

A. Reduce reflections on transmission lines ✔
B. Increase reflections
C. Store charge
D. Add noise

Correct answer: A. Reduce reflections on transmission lines

61. Power integrity focuses on:

A. Mechanical fit
B. Silkscreen
C. Signal timing only
D. Delivering stable, low-noise power to all components ✔

Correct answer: D. Delivering stable, low-noise power to all components

62. A power distribution network (PDN) includes:

A. Only connectors
B. Only labels
C. Regulators, planes, traces and decoupling capacitors ✔
D. Only signals

Correct answer: C. Regulators, planes, traces and decoupling capacitors

63. Wide copper pours for power help to:

A. Increase noise
B. Block signals
C. Reduce resistance and voltage drop ✔
D. Add heat

Correct answer: C. Reduce resistance and voltage drop

64. Thermal relief pads help to:

A. Remove copper
B. Increase heat flow during soldering
C. Make soldering easier on pads connected to large copper areas ✔
D. Add vias

Correct answer: C. Make soldering easier on pads connected to large copper areas

65. Thermal vias under power components:

A. Increase temperature
B. Block airflow
C. Conduct heat to other layers or heatsinks ✔
D. Carry signals only

Correct answer: C. Conduct heat to other layers or heatsinks

66. Crystal oscillators should be placed:

A. Far away with long traces
B. Near antennas
C. Under connectors
D. Close to the IC with short traces and a ground guard ✔

Correct answer: D. Close to the IC with short traces and a ground guard

67. Analog and digital sections should be:

A. Overlapping
B. Mixed randomly
C. Separated to reduce noise coupling ✔
D. On the same traces

Correct answer: C. Separated to reduce noise coupling

68. Antenna keep-out areas require:

A. Ground planes under antennas always
B. Large components
C. Dense copper fill
D. No copper or components near the antenna region ✔

Correct answer: D. No copper or components near the antenna region

69. EMI can be reduced on PCBs by:

A. Removing ground
B. Higher edge rates always
C. Short return paths, solid ground planes and filtering ✔
D. Long loops

Correct answer: C. Short return paths, solid ground planes and filtering

70. ESD protection devices should be placed:

A. In the board centre
B. Near connectors where discharge enters ✔
C. Nowhere
D. Far from connectors

Correct answer: B. Near connectors where discharge enters

71. Fiducial marks help:

A. Pick-and-place machines align the board optically ✔
B. Heat dissipation
C. Labelling only
D. Electrical conduction

Correct answer: A. Pick-and-place machines align the board optically

72. Test points allow:

A. Routing power
B. Decoration
C. Probing signals during manufacturing and debugging ✔
D. Mounting the board

Correct answer: C. Probing signals during manufacturing and debugging

73. Panelisation means:

A. Removing vias
B. Combining multiple boards on one panel for efficient manufacturing ✔
C. Splitting layers
D. Adding labels

Correct answer: B. Combining multiple boards on one panel for efficient manufacturing

74. V-scoring and mouse bites are used for:

A. Testing
B. Routing signals
C. Soldering
D. Separating boards from a panel ✔

Correct answer: D. Separating boards from a panel

75. Gerber files contain:

A. Firmware
B. Image data for each copper, mask and silkscreen layer ✔
C. Schematics only
D. BOM prices

Correct answer: B. Image data for each copper, mask and silkscreen layer

Questions 76 to 100

76. NC drill files specify:

A. Layer colours
B. Component values
C. Trace widths
D. Hole locations and sizes ✔

Correct answer: D. Hole locations and sizes

77. A pick-and-place (centroid) file lists:

A. Prices
B. Component positions and rotations for assembly machines ✔
C. Hole sizes
D. Net names only

Correct answer: B. Component positions and rotations for assembly machines

78. A BOM should include:

A. Only colours
B. Only drill sizes
C. Part numbers, values, quantities and reference designators ✔
D. Only board size

Correct answer: C. Part numbers, values, quantities and reference designators

79. ODB++ and IPC-2581 are:

A. Intelligent data formats for PCB manufacturing ✔
B. Programming languages
C. Solder alloys
D. Component types

Correct answer: A. Intelligent data formats for PCB manufacturing

80. SMT stands for:

A. Standard metal trace
B. Single-mode transmission
C. Surface-mount technology ✔
D. Silicon mask technique

Correct answer: C. Surface-mount technology

81. Reflow soldering uses:

A. Wave baths only
B. Glue
C. A soldering iron only
D. Solder paste and controlled heating profiles ✔

Correct answer: D. Solder paste and controlled heating profiles

82. Wave soldering is commonly used for:

A. Silkscreen
B. Microvias
C. Through-hole components ✔
D. Fine-pitch BGAs

Correct answer: C. Through-hole components

83. A solder paste stencil defines:

A. Where paste is applied on SMD pads ✔
B. Component values
C. Drill locations
D. Copper traces

Correct answer: A. Where paste is applied on SMD pads

84. BGA packages require:

A. No routing
B. Careful fan-out routing and often X-ray inspection ✔
C. Through-hole pads
D. Only hand soldering

Correct answer: B. Careful fan-out routing and often X-ray inspection

85. Tombstoning is a defect where:

A. A board breaks
B. Traces short
C. Vias fill
D. A small component lifts on one end during reflow ✔

Correct answer: D. A small component lifts on one end during reflow

86. AOI (Automated Optical Inspection) checks:

A. Prices
B. Assembled boards for placement and soldering defects ✔
C. Firmware
D. Schematics

Correct answer: B. Assembled boards for placement and soldering defects

87. DFM (Design for Manufacturing) ensures:

A. Colours match
B. The design can be fabricated reliably at reasonable cost ✔
C. Marketing approves
D. Firmware runs

Correct answer: B. The design can be fabricated reliably at reasonable cost

88. DFA (Design for Assembly) focuses on:

A. Drill files only
B. Making components easy to place and solder ✔
C. Firmware design
D. Testing only

Correct answer: B. Making components easy to place and solder

89. Flex PCBs are useful for:

A. Breadboards
B. High-power transformers
C. Applications requiring bending or tight spaces ✔
D. Only rigid enclosures

Correct answer: C. Applications requiring bending or tight spaces

90. Rigid-flex boards combine:

A. Rigid sections connected by flexible circuits ✔
B. Two rigid boards with wires
C. Only ceramic
D. Only flex layers

Correct answer: A. Rigid sections connected by flexible circuits

91. Metal-core PCBs are used for:

A. Paper circuits
B. Low-power sensors only
C. High-power LEDs needing good heat dissipation ✔
D. Flexible wearables

Correct answer: C. High-power LEDs needing good heat dissipation

92. High-frequency RF boards often use:

A. Glass only
B. Cardboard
C. Only FR-4 always
D. Low-loss materials such as Rogers laminates ✔

Correct answer: D. Low-loss materials such as Rogers laminates

93. Popular PCB design tools include:

A. KiCad, Altium Designer, OrCAD and Eagle ✔
B. Premiere
C. Photoshop
D. Excel

Correct answer: A. KiCad, Altium Designer, OrCAD and Eagle

94. KiCad is:

A. A paid simulator only
B. A compiler
C. A CAM tool only
D. A free, open-source PCB design suite ✔

Correct answer: D. A free, open-source PCB design suite

95. 3D models in PCB tools help to:

A. Change prices
B. Route faster
C. Write firmware
D. Check mechanical fit with enclosures ✔

Correct answer: D. Check mechanical fit with enclosures

96. Design reviews before fabrication help to:

A. Catch errors early and avoid costly respins ✔
B. Increase defects
C. Skip testing
D. Delay projects

Correct answer: A. Catch errors early and avoid costly respins

97. The main goal of good PCB design is:

A. The most layers possible
B. Ignoring standards
C. The smallest board at any cost
D. A reliable, manufacturable board meeting electrical and mechanical requirements ✔

Correct answer: D. A reliable, manufacturable board meeting electrical and mechanical requirements

98. Teardrops at pad-trace junctions help to:

A. Strengthen connections and reduce drilling breakout ✔
B. Increase impedance
C. Add labels
D. Block solder

Correct answer: A. Strengthen connections and reduce drilling breakout

99. Creepage distance is important for:

A. Low-voltage logic only
B. High-voltage isolation along the board surface ✔
C. Fiducials
D. Silkscreen

Correct answer: B. High-voltage isolation along the board surface

100. Mounting holes should be:

A. Omitted always
B. Placed over traces
C. Plated through signals
D. Placed with clearance from traces and components ✔

Correct answer: D. Placed with clearance from traces and components

How to Pass the PCB Design Exam

  • Read every question carefully; most options look similar, so look for the most precise answer.
  • Revise the questions above topic by topic rather than memorising letters, because option order can change in the live test.
  • You need 80 correct answers out of 100 to pass, so aim to understand at least 85 to stay safe.
  • If you do not clear it on the first attempt, review the questions you missed and use the retake option.

Frequently Asked Questions

How many questions are in the PCB Design Professional Certification exam?

The exam has 100 multiple-choice questions, each worth 1 mark.

What is the passing score for the PCB Design Professional Certification?

You need at least 80% (80 out of 100) to pass and receive the certificate.

Can I retake the PCB Design Professional Certification exam?

Yes. If you score below 80%, you can retry the test after reviewing the topics.

Is the Itronix certificate verifiable?

Yes. Every certificate issued by Itronix Solutions has a unique ID that can be checked on the Itronix verify-certificate page.

More Electronics & Hardware Certification Answers

Disclaimer: These answers are provided for learning and revision. Questions and answers are checked regularly; if you find a mistake, let us know in the comments.

About Priya Dogra

Priya Dogra runs priyadogra.com, where she shares free certification courses, internships, jobs, scholarships and exam preparation guides for Indian students and freshers. Follow her on YouTube, LinkedIn and Instagram for the latest opportunities.

Check Also

Unix/ Linux Certification exam answers 2026

Unix/ Linux Certification Exam Answers 2026 (All 100 Questions)

All 100 Unix/ Linux Certification exam questions with correct answers highlighted - updated 2026.

Leave a Reply

Your email address will not be published. Required fields are marked *