Wednesday , November 18 2026
Breaking News

Computer Architecture and Organization Professional Certification Exam Answers 2026 (All 100 Questions)

Computer Architecture and Organization Professional Certification exam answers 2026: This page lists all 100 questions of the official Computer Architecture and Organization Professional Certification exam by Itronix Solutions, each with its four answer options and the correct answer highlighted in green. Use it to revise every topic before you attempt the test and earn your verifiable certificate.

About this certification: Understand computer architecture with this certification. It covers CPU design, memory hierarchy, and instruction sets. Ideal for system architects and hardware engineers.

Certification Computer Architecture and Organization Professional Certification
Provider Itronix Solutions
Category Electronics & Hardware
Total questions 100 multiple-choice questions
Marks 1 mark per question (100 marks)
Passing score 80% (80 out of 100)
Retake Available if you do not pass
Certificate Verifiable online certificate

Take the exam: Computer Architecture and Organization Professional Certification on Itronix Solutions. See every other Itronix exam in our complete list of Itronix certification answers.

Computer Architecture and Organization Exam Questions and Answers

Questions 1 to 25

1. What is the primary function of the control unit in a computer system?

A. A) To perform arithmetic and logical operations
B. B) To direct the operation of the processor ✔
C. C) To store data and instructions
D. D) To handle input and output operations

Correct answer: B. B) To direct the operation of the processor

2. What type of memory is used to store the most frequently accessed data for quick retrieval?

A. A) Cache memory ✔
B. B) ROM
C. C) RAM
D. D) Register

Correct answer: A. A) Cache memory

3. Which of the following is an example of volatile memory?

A. A) ROM
B. B) Flash memory
C. C) RAM ✔
D. D) Hard disk

Correct answer: C. C) RAM

4. What is the primary function of the ALU (Arithmetic Logic Unit)?

A. A) To perform arithmetic and logical operations ✔
B. B) To store data
C. C) To decode instructions
D. D) To manage memory

Correct answer: A. A) To perform arithmetic and logical operations

5. What is the size of the address bus in a 32-bit processor?

A. A) 8 bits
B. B) 16 bits
C. C) 32 bits ✔
D. D) 64 bits

Correct answer: C. C) 32 bits

6. Which architecture allows separate storage and signal paths for instructions and data?

A. A) Harvard architecture ✔
B. B) Von Neumann architecture
C. C) RISC architecture
D. D) CISC architecture

Correct answer: A. A) Harvard architecture

7. What is the main advantage of using pipelining in a processor?

A. A) Reduced cost
B. B) Increased instruction throughput ✔
C. C) Increased memory capacity
D. D) Reduced power consumption

Correct answer: B. B) Increased instruction throughput

8. Which register stores the address of the next instruction to be executed?

A. A) Stack Pointer
B. B) Program Counter (PC) ✔
C. C) Instruction Register
D. D) Base Register

Correct answer: B. B) Program Counter (PC)

9. What type of addressing mode uses a constant value directly in the instruction?

A. A) Direct Addressing
B. B) Indirect Addressing
C. C) Immediate Addressing ✔
D. D) Indexed Addressing

Correct answer: C. C) Immediate Addressing

10. What is the role of a cache memory in a computer system?

A. A) To store permanent data
B. B) To store frequently accessed data for quick retrieval ✔
C. C) To store machine instructions
D. D) To store large files

Correct answer: B. B) To store frequently accessed data for quick retrieval

11. What does DMA (Direct Memory Access) allow a device to do?

A. A) Access cache directly
B. B) Transfer data directly between memory and I/O without CPU intervention ✔
C. C) Perform parallel processing
D. D) Execute instructions from memory

Correct answer: B. B) Transfer data directly between memory and I/O without CPU intervention

12. What type of memory is used to store the BIOS in a computer?

A. A) ROM ✔
B. B) RAM
C. C) Cache
D. D) DRAM

Correct answer: A. A) ROM

13. Which instruction set architecture (ISA) is based on a small, highly optimized set of instructions?

A. A) CISC
B. B) RISC ✔
C. C) MISC
D. D) Complex architecture

Correct answer: B. B) RISC

14. What is the purpose of the instruction register in a processor?

A. A) To store the current instruction being executed ✔
B. B) To store memory addresses
C. C) To store data
D. D) To control program flow

Correct answer: A. A) To store the current instruction being executed

15. What does the term "bus width" refer to in computer architecture?

A. A) The physical size of the CPU
B. B) The speed of the processor
C. C) The number of bits that can be transmitted simultaneously ✔
D. D) The size of the instruction set

Correct answer: C. C) The number of bits that can be transmitted simultaneously

16. What is the primary function of the memory management unit (MMU)?

A. A) To handle memory addressing and protection ✔
B. B) To store data temporarily
C. C) To execute machine instructions
D. D) To perform arithmetic calculations

Correct answer: A. A) To handle memory addressing and protection

17. What is the difference between a superscalar processor and a scalar processor?

A. A) Superscalar processors have fewer registers
B. B) Superscalar processors can execute multiple instructions per clock cycle ✔
C. C) Scalar processors have larger cache sizes
D. D) Scalar processors have a higher clock speed

Correct answer: B. B) Superscalar processors can execute multiple instructions per clock cycle

18. In which type of memory are program instructions typically stored during execution?

A. A) Cache memory
B. B) RAM ✔
C. C) ROM
D. D) Hard disk

Correct answer: B. B) RAM

19. Which component connects the CPU to the memory and I/O devices?

A. A) System bus ✔
B. B) Memory controller
C. C) DMA
D. D) Address register

Correct answer: A. A) System bus

20. What is the purpose of branch prediction in a CPU?

A. A) To increase instruction length
B. B) To simplify instruction decoding
C. C) To improve instruction pipeline efficiency ✔
D. D) To store temporary data

Correct answer: C. C) To improve instruction pipeline efficiency

21. Computer architecture describes:

A. Only the cabinet design
B. The attributes of a system visible to the programmer, such as the instruction set ✔
C. Only software licensing
D. Only the physical wiring

Correct answer: B. The attributes of a system visible to the programmer, such as the instruction set

22. Computer organisation describes:

A. Only the operating system
B. Only programming languages
C. How architectural specifications are implemented in hardware ✔
D. Only the instruction set

Correct answer: C. How architectural specifications are implemented in hardware

23. The von Neumann architecture uses:

A. No memory
B. Separate memories for code and data
C. Only registers
D. A single shared memory for instructions and data ✔

Correct answer: D. A single shared memory for instructions and data

24. The Harvard architecture uses:

A. Only cache
B. No buses
C. One shared memory
D. Separate memories and buses for instructions and data ✔

Correct answer: D. Separate memories and buses for instructions and data

25. The von Neumann bottleneck refers to:

A. Fast I/O
B. Limited throughput between CPU and memory over a shared bus ✔
C. Excess cache
D. Too many registers

Correct answer: B. Limited throughput between CPU and memory over a shared bus

Questions 26 to 50

26. The main components of a CPU are:

A. ALU, control unit and registers ✔
B. Monitor and keyboard
C. Power supply only
D. Hard disk and printer

Correct answer: A. ALU, control unit and registers

27. The ALU performs:

A. Instruction fetch only
B. Memory refresh
C. Power management
D. Arithmetic and logical operations ✔

Correct answer: D. Arithmetic and logical operations

28. The control unit:

A. Displays output
B. Performs floating-point only
C. Decodes instructions and generates control signals ✔
D. Stores data permanently

Correct answer: C. Decodes instructions and generates control signals

29. The program counter (PC) holds:

A. The stack contents
B. The address of the next instruction ✔
C. The current data value
D. The cache size

Correct answer: B. The address of the next instruction

30. The instruction register (IR) holds:

A. The next address
B. Interrupt vectors
C. Cache tags
D. The instruction currently being executed ✔

Correct answer: D. The instruction currently being executed

31. The memory address register (MAR) holds:

A. The instruction
B. Data being written
C. Flags
D. The address of the memory location being accessed ✔

Correct answer: D. The address of the memory location being accessed

32. The memory data register (MDR) holds:

A. An address
B. Data being transferred to or from memory ✔
C. The program counter
D. The opcode only

Correct answer: B. Data being transferred to or from memory

33. The instruction cycle consists of:

A. Compile, link, run
B. Boot, load, quit
C. Fetch, decode, execute and store stages ✔
D. Read, print, exit

Correct answer: C. Fetch, decode, execute and store stages

34. An instruction set architecture (ISA) defines:

A. Operating system GUI
B. Instructions, registers, data types and addressing modes ✔
C. Software applications
D. Physical chip layout only

Correct answer: B. Instructions, registers, data types and addressing modes

35. RISC architectures emphasise:

A. Simple, fixed-length instructions executed quickly ✔
B. Many complex variable-length instructions
C. Microcode only
D. No registers

Correct answer: A. Simple, fixed-length instructions executed quickly

36. CISC architectures emphasise:

A. Fixed-length only
B. No memory access
C. Only simple instructions
D. Complex instructions that can do more work per instruction ✔

Correct answer: D. Complex instructions that can do more work per instruction

37. Examples of RISC ISAs include:

A. VAX
B. x86
C. ARM and RISC-V ✔
D. IBM System/360

Correct answer: C. ARM and RISC-V

38. x86 is generally classified as:

A. RISC
B. Dataflow
C. CISC ✔
D. VLIW only

Correct answer: C. CISC

39. Load/store architecture means:

A. All instructions access memory
B. Only load and store instructions access memory ✔
C. Only registers exist
D. No memory access

Correct answer: B. Only load and store instructions access memory

40. An opcode specifies:

A. The cache line
B. The operation an instruction performs ✔
C. The clock speed
D. The memory size

Correct answer: B. The operation an instruction performs

41. Immediate addressing means:

A. The operand is in a register pointed to
B. No operand exists
C. The operand value is contained in the instruction ✔
D. The operand is in memory

Correct answer: C. The operand value is contained in the instruction

42. Register indirect addressing means:

A. A register holds the memory address of the operand ✔
B. The instruction holds the value
C. No register is used
D. The PC holds data

Correct answer: A. A register holds the memory address of the operand

43. Indexed addressing computes the address as:

A. Random
B. Only the PC
C. A base address plus an index register value ✔
D. Only a constant

Correct answer: C. A base address plus an index register value

44. Two’s complement is used to represent:

A. Characters
B. Addresses only
C. Signed integers in binary ✔
D. Floating-point only

Correct answer: C. Signed integers in binary

45. In two’s complement, the most significant bit indicates:

A. The exponent
B. Nothing
C. The parity
D. The sign of the number ✔

Correct answer: D. The sign of the number

46. Overflow occurs when:

A. Memory is full
B. Cache misses
C. A result is zero
D. A result exceeds the range representable by the bits ✔

Correct answer: D. A result exceeds the range representable by the bits

47. IEEE 754 defines:

A. Network packets
B. Floating-point number representation ✔
C. Integer division
D. Bus timing

Correct answer: B. Floating-point number representation

48. A floating-point number consists of:

A. Only digits
B. Only an integer
C. Sign, exponent and mantissa (significand) ✔
D. Only a sign

Correct answer: C. Sign, exponent and mantissa (significand)

49. Booth’s algorithm is used for:

A. Efficient signed binary multiplication ✔
B. Sorting
C. Division by zero
D. Cache replacement

Correct answer: A. Efficient signed binary multiplication

50. A carry-lookahead adder improves on a ripple-carry adder by:

A. Using memory
B. Using fewer gates always
C. Removing carries
D. Computing carries in parallel to reduce delay ✔

Correct answer: D. Computing carries in parallel to reduce delay

Questions 51 to 75

51. Microprogrammed control units:

A. Use only hardwired gates
B. Generate control signals from microinstructions stored in control memory ✔
C. Cannot be changed
D. Have no control store

Correct answer: B. Generate control signals from microinstructions stored in control memory

52. Hardwired control units are:

A. Faster but harder to modify than microprogrammed ones ✔
B. Slower and easier to modify
C. Software-based
D. Memory-based

Correct answer: A. Faster but harder to modify than microprogrammed ones

53. The memory hierarchy is organised by:

A. Brand
B. Speed, cost and capacity, from registers to storage ✔
C. Alphabet
D. Colour

Correct answer: B. Speed, cost and capacity, from registers to storage

54. The fastest storage in the hierarchy is:

A. CPU registers ✔
B. Main memory
C. Tape
D. Hard disks

Correct answer: A. CPU registers

55. Cache memory exists to:

A. Store backups
B. Reduce average memory access time ✔
C. Replace RAM
D. Increase disk size

Correct answer: B. Reduce average memory access time

56. Temporal locality means:

A. Nearby data will be accessed
B. Recently accessed data is likely to be accessed again soon ✔
C. Data is random
D. Data never repeats

Correct answer: B. Recently accessed data is likely to be accessed again soon

57. Spatial locality means:

A. Data is random
B. Data is reused over time only
C. Only instructions are cached
D. Data near recently accessed addresses is likely to be accessed ✔

Correct answer: D. Data near recently accessed addresses is likely to be accessed

58. A cache hit occurs when:

A. Requested data is found in the cache ✔
B. The CPU stops
C. Data is not in cache
D. Memory fails

Correct answer: A. Requested data is found in the cache

59. Hit ratio is:

A. Cache size divided by memory
B. The fraction of accesses found in the cache ✔
C. The clock rate
D. The miss penalty

Correct answer: B. The fraction of accesses found in the cache

60. Direct-mapped cache maps each memory block to:

A. No line
B. Two lines always
C. Any line
D. Exactly one cache line ✔

Correct answer: D. Exactly one cache line

61. Fully associative cache allows a block to be placed:

A. Nowhere
B. In any cache line ✔
C. In only one line
D. Only in registers

Correct answer: B. In any cache line

62. Set-associative cache is:

A. A compromise where a block maps to any line within one set ✔
B. Identical to fully associative
C. Not a cache
D. Identical to direct-mapped

Correct answer: A. A compromise where a block maps to any line within one set

63. A cache address is divided into:

A. Tag, index and block offset ✔
B. Page and frame only
C. Sign and exponent
D. Opcode and operand

Correct answer: A. Tag, index and block offset

64. LRU replacement policy evicts:

A. The most recently used block
B. The newest block
C. A random block always
D. The least recently used block ✔

Correct answer: D. The least recently used block

65. Write-through caches:

A. Never update memory
B. Do not support writes
C. Update memory only on eviction
D. Update main memory on every write ✔

Correct answer: D. Update main memory on every write

66. Write-back caches:

A. Update main memory only when a dirty block is evicted ✔
B. Update memory on every write
C. Disable caching
D. Never store writes

Correct answer: A. Update main memory only when a dirty block is evicted

67. A dirty bit indicates:

A. A block is empty
B. A block is invalid
C. A block is read-only
D. A cache block has been modified ✔

Correct answer: D. A cache block has been modified

68. Multi-level caches (L1, L2, L3) are used to:

A. Balance speed and capacity ✔
B. Store files
C. Replace main memory
D. Increase latency

Correct answer: A. Balance speed and capacity

69. Cache coherence protocols such as MESI ensure:

A. Faster disks
B. Multiple cores see consistent data ✔
C. Lower voltage
D. More registers

Correct answer: B. Multiple cores see consistent data

70. Virtual memory allows:

A. Disk-free operation
B. Only physical addresses
C. Programs to use more address space than physical RAM ✔
D. No paging

Correct answer: C. Programs to use more address space than physical RAM

71. Paging divides memory into:

A. Cache lines only
B. Fixed-size pages and frames ✔
C. Registers
D. Variable segments only

Correct answer: B. Fixed-size pages and frames

72. The page table maps:

A. Files to folders
B. Cache tags
C. Instructions to opcodes
D. Virtual pages to physical frames ✔

Correct answer: D. Virtual pages to physical frames

73. A TLB (Translation Lookaside Buffer) is:

A. A bus
B. A register file
C. A disk buffer
D. A cache for recent virtual-to-physical address translations ✔

Correct answer: D. A cache for recent virtual-to-physical address translations

74. A page fault occurs when:

A. A referenced page is not in physical memory ✔
B. Memory is empty
C. The TLB hits
D. A cache hits

Correct answer: A. A referenced page is not in physical memory

75. Segmentation divides memory into:

A. Cache lines
B. Fixed pages only
C. Variable-size logical segments ✔
D. Registers

Correct answer: C. Variable-size logical segments

Questions 76 to 100

76. Main memory is usually built from:

A. Magnetic tape
B. Flash only
C. SRAM only
D. DRAM ✔

Correct answer: D. DRAM

77. SRAM differs from DRAM because SRAM:

A. Is faster and does not need refresh but costs more per bit ✔
B. Needs constant refresh
C. Is non-volatile
D. Is slower and cheaper

Correct answer: A. Is faster and does not need refresh but costs more per bit

78. Memory interleaving improves:

A. Disk capacity
B. Bandwidth by spreading consecutive addresses across banks ✔
C. Cache size
D. Latency of a single access always

Correct answer: B. Bandwidth by spreading consecutive addresses across banks

79. Pipelining in a CPU allows:

A. Slower execution always
B. No clock
C. Multiple instructions to overlap in different stages ✔
D. Only one instruction at a time

Correct answer: C. Multiple instructions to overlap in different stages

80. A classic five-stage RISC pipeline includes:

A. IF, ID, EX, MEM and WB ✔
B. Read, write only
C. Boot, run, stop, save, quit
D. Fetch only

Correct answer: A. IF, ID, EX, MEM and WB

81. Structural hazards occur when:

A. Data dependencies exist
B. Branches occur
C. Two instructions need the same hardware resource at once ✔
D. Cache hits

Correct answer: C. Two instructions need the same hardware resource at once

82. Data hazards occur when:

A. Memory is full
B. An instruction depends on the result of a previous instruction still in the pipeline ✔
C. Branches are taken
D. Resources conflict

Correct answer: B. An instruction depends on the result of a previous instruction still in the pipeline

83. Forwarding (bypassing) resolves data hazards by:

A. Flushing memory
B. Adding registers
C. Passing results directly between pipeline stages ✔
D. Stalling forever

Correct answer: C. Passing results directly between pipeline stages

84. Control hazards are caused by:

A. Branch and jump instructions ✔
B. Register count
C. Arithmetic only
D. Cache size

Correct answer: A. Branch and jump instructions

85. Branch prediction aims to:

A. Guess branch outcomes to keep the pipeline full ✔
B. Slow the CPU
C. Increase hazards
D. Remove branches

Correct answer: A. Guess branch outcomes to keep the pipeline full

86. Superscalar processors:

A. Issue multiple instructions per clock cycle ✔
B. Issue one instruction every few cycles
C. Have no pipeline
D. Use no registers

Correct answer: A. Issue multiple instructions per clock cycle

87. Out-of-order execution allows:

A. Only in-order execution
B. No parallelism
C. Instructions to execute as operands become ready rather than strictly in program order ✔
D. No registers

Correct answer: C. Instructions to execute as operands become ready rather than strictly in program order

88. Register renaming eliminates:

A. True data dependencies
B. False dependencies such as WAR and WAW hazards ✔
C. Cache misses
D. Branches

Correct answer: B. False dependencies such as WAR and WAW hazards

89. CPU performance time equals:

A. Bus width only
B. Instruction count x CPI x clock cycle time ✔
C. Cache size x RAM
D. Clock rate x memory

Correct answer: B. Instruction count x CPI x clock cycle time

90. CPI stands for:

A. Clocks per interrupt
B. Cache performance index
C. Cycles per instruction ✔
D. Core power indicator

Correct answer: C. Cycles per instruction

91. Amdahl’s law states that:

A. Speedup is limited by the fraction of work that cannot be improved ✔
B. Cache always helps
C. Clock rates double yearly
D. Speedup is unlimited

Correct answer: A. Speedup is limited by the fraction of work that cannot be improved

92. MIPS as a performance metric means:

A. Maximum interrupt speed
B. Multiple input processors
C. Memory in pages
D. Millions of instructions per second ✔

Correct answer: D. Millions of instructions per second

93. Programmed I/O requires:

A. DMA only
B. No CPU involvement
C. The CPU to actively poll and transfer data ✔
D. Interrupts only

Correct answer: C. The CPU to actively poll and transfer data

94. Interrupt-driven I/O lets devices:

A. Signal the CPU when they need attention ✔
B. Never contact the CPU
C. Run without power
D. Bypass memory

Correct answer: A. Signal the CPU when they need attention

95. DMA transfers data:

A. Between I/O devices and memory without continuous CPU involvement ✔
B. Only to registers
C. Only to cache
D. Only through the CPU

Correct answer: A. Between I/O devices and memory without continuous CPU involvement

96. Buses in a computer include:

A. Only USB
B. Only power buses
C. Only network buses
D. Address, data and control buses ✔

Correct answer: D. Address, data and control buses

97. Bus arbitration decides:

A. Clock speed
B. Cache size
C. Instruction format
D. Which device gets control of the shared bus ✔

Correct answer: D. Which device gets control of the shared bus

98. Flynn’s taxonomy classifies architectures as:

A. L1 and L2
B. SISD, SIMD, MISD and MIMD ✔
C. DRAM and SRAM
D. RISC and CISC only

Correct answer: B. SISD, SIMD, MISD and MIMD

99. SIMD architectures execute:

A. Nothing in parallel
B. Multiple instructions on one data item
C. One instruction on multiple data elements simultaneously ✔
D. One instruction on one data item

Correct answer: C. One instruction on multiple data elements simultaneously

100. Multicore processors are an example of:

A. MIMD parallelism ✔
B. SISD
C. Single-cycle design
D. Microprogramming

Correct answer: A. MIMD parallelism

How to Pass the Computer Architecture and Organization Exam

  • Read every question carefully; most options look similar, so look for the most precise answer.
  • Revise the questions above topic by topic rather than memorising letters, because option order can change in the live test.
  • You need 80 correct answers out of 100 to pass, so aim to understand at least 85 to stay safe.
  • If you do not clear it on the first attempt, review the questions you missed and use the retake option.

Frequently Asked Questions

How many questions are in the Computer Architecture and Organization Professional Certification exam?

The exam has 100 multiple-choice questions, each worth 1 mark.

What is the passing score for the Computer Architecture and Organization Professional Certification?

You need at least 80% (80 out of 100) to pass and receive the certificate.

Can I retake the Computer Architecture and Organization Professional Certification exam?

Yes. If you score below 80%, you can retry the test after reviewing the topics.

Is the Itronix certificate verifiable?

Yes. Every certificate issued by Itronix Solutions has a unique ID that can be checked on the Itronix verify-certificate page.

More Electronics & Hardware Certification Answers

Disclaimer: These answers are provided for learning and revision. Questions and answers are checked regularly; if you find a mistake, let us know in the comments.

About Priya Dogra

Priya Dogra runs priyadogra.com, where she shares free certification courses, internships, jobs, scholarships and exam preparation guides for Indian students and freshers. Follow her on YouTube, LinkedIn and Instagram for the latest opportunities.

Check Also

Unix/ Linux Certification exam answers 2026

Unix/ Linux Certification Exam Answers 2026 (All 100 Questions)

All 100 Unix/ Linux Certification exam questions with correct answers highlighted - updated 2026.

Leave a Reply

Your email address will not be published. Required fields are marked *