Certified Quality Engineer Professional Certification exam answers 2026: This page lists all 100 questions of the official Certified Quality Engineer Professional Certification exam by Itronix Solutions, each with its four answer options and the correct answer highlighted in green. Use it to revise every topic before you attempt the test and earn your verifiable certificate.
About this certification: The Certified Quality Engineer (CQE) is a professional certification offered by the Itronix Solutions .
| Certification | Certified Quality Engineer Professional Certification |
| Provider | Itronix Solutions |
| Category | Programming & Development |
| Total questions | 100 multiple-choice questions |
| Marks | 1 mark per question (100 marks) |
| Passing score | 80% (80 out of 100) |
| Retake | Available if you do not pass |
| Certificate | Verifiable online certificate |
Take the exam: Certified Quality Engineer Professional Certification on Itronix Solutions. See every other Itronix exam in our complete list of Itronix certification answers.
Certified Quality Engineer Exam Questions and Answers
Questions 1 to 25
1. What is the minimum number of years of professional experience required to be eligible for the CQE exam?
Correct answer: C. 3 years
2. Which of the following is NOT one of the main domains covered in the CQE exam?
Correct answer: C. Risk Management
3. To maintain the CQE certification, how many Recertification Units (RUs) must a certified professional earn within a three-year certification cycle?
Correct answer: B. 15 RUs
4. Which statistical tool is commonly used for analyzing the variation in a process and identifying potential areas for improvement?
Correct answer: C. Control Chart
5. What is the primary purpose of a Design of Experiments (DOE) in quality engineering?
Correct answer: C. To optimize product designs and processes
6. In the context of quality management, what does the acronym DMAIC stand for?
Correct answer: A. Define, Measure, Analyze, Improve, Control
7. Which quality management pioneer is known for the 14 Points for Total Quality Management (TQM)?
Correct answer: B. W. Edwards Deming
8. What is the main objective of a Failure Mode and Effects Analysis (FMEA
Correct answer: A. To identify and prioritize potential failure modes in a process or product
9. Which tool is commonly used to visualize the sequence of steps in a process and identify areas for improvement?
Correct answer: C. Flowchart
10. Which of the following quality management standards is recognized internationally and focuses on environmental management systems?
Correct answer: B. ISO 14001
11. What is the primary purpose of a Gage R&R (Gage Repeatability and Reproducibility) study?
Correct answer: B. To evaluate the precision and accuracy of a measurement system
12. In the context of quality improvement, what does the acronym PDPC stand for?
Correct answer: A. Process Diagram for Problem Clarification
13. Which quality control chart is used to monitor the number of defects or nonconformities in a sample over time?
Correct answer: B. Control Chart
14. What type of data is typically represented by discrete values and can be counted, but not measured on a continuous scale?
Correct answer: C. Categorical data
15. Which of the following is NOT a key element of the Plan-Do-Check-Act (PDCA) cycle?
Correct answer: B. Train
16. Quality is commonly defined as:
Correct answer: B. Fitness for use or conformance to requirements
17. Total Quality Management (TQM) emphasises:
Correct answer: B. Organisation-wide continuous improvement and customer focus
18. Who is associated with the 14 Points for management?
Correct answer: A. W. Edwards Deming
19. Joseph Juran’s quality trilogy consists of:
Correct answer: A. Quality planning, quality control and quality improvement
20. Philip Crosby is known for the concept of:
Correct answer: D. Zero defects
21. The PDCA cycle stands for:
Correct answer: C. Plan, Do, Check, Act
22. Kaizen means:
Correct answer: B. Continuous incremental improvement
23. The cost of quality includes:
Correct answer: B. Prevention, appraisal, internal failure and external failure costs
24. Prevention costs include:
Correct answer: D. Training and process planning
25. Appraisal costs include:
Correct answer: B. Inspection and testing
Questions 26 to 50
26. Internal failure costs occur:
Correct answer: C. Before the product reaches the customer
27. External failure costs include:
Correct answer: C. Warranty claims and returns
28. ISO 9001 is a standard for:
Correct answer: B. Quality management systems
29. ISO 14001 relates to:
Correct answer: A. Environmental management systems
30. An internal audit is conducted by:
Correct answer: B. The organisation itself to check its own system
31. A nonconformity is:
Correct answer: C. A failure to meet a specified requirement
32. Corrective action aims to:
Correct answer: B. Eliminate the cause of a detected nonconformity
33. Preventive action aims to:
Correct answer: D. Eliminate the cause of a potential nonconformity
34. Root cause analysis seeks to:
Correct answer: A. Identify the fundamental cause of a problem
35. The 5 Whys technique involves:
Correct answer: A. Repeatedly asking why to reach the root cause
36. A fishbone diagram is also called:
Correct answer: B. Ishikawa or cause-and-effect diagram
37. Common fishbone categories (6M) include:
Correct answer: D. Man, Machine, Method, Material, Measurement and Mother Nature
38. A Pareto chart is based on the principle that:
Correct answer: A. A few causes account for most problems
39. The Pareto principle is often called the:
Correct answer: A. 80/20 rule
40. A check sheet is used to:
Correct answer: A. Collect and tally data systematically
41. A histogram shows:
Correct answer: A. The frequency distribution of data
42. A scatter diagram shows:
Correct answer: B. The relationship between two variables
43. A flowchart shows:
Correct answer: A. The sequence of steps in a process
44. A control chart is used to:
Correct answer: A. Monitor process stability over time
45. Control limits are typically set at:
Correct answer: B. Plus or minus three standard deviations from the mean
46. Specification limits are defined by:
Correct answer: B. Customer or design requirements
47. Common cause variation is:
Correct answer: D. Natural, inherent variation in a stable process
48. Special cause variation is:
Correct answer: B. Variation from an assignable, unusual source
49. An X-bar and R chart is used for:
Correct answer: C. Variables data in subgroups
50. A p-chart monitors:
Correct answer: C. The proportion of defective units
Questions 51 to 75
51. A c-chart monitors:
Correct answer: A. The count of defects per unit or area
52. A point outside control limits suggests:
Correct answer: C. A special cause may be present
53. Process capability compares:
Correct answer: A. Process variation with specification limits
54. Cp measures:
Correct answer: D. Potential capability assuming the process is centred
55. Cpk accounts for:
Correct answer: D. Both process spread and centring
56. A Cpk of at least 1.33 is often considered:
Correct answer: D. Capable for many industries
57. Six Sigma aims for about:
Correct answer: B. 3.4 defects per million opportunities
58. DMAIC stands for:
Correct answer: B. Define, Measure, Analyse, Improve, Control
59. DMADV is used for:
Correct answer: D. Designing new processes or products
60. Lean focuses on:
Correct answer: A. Eliminating waste and improving flow
61. The 8 wastes in Lean include:
Correct answer: B. Defects, overproduction, waiting and excess inventory
62. 5S stands for:
Correct answer: B. Sort, Set in order, Shine, Standardise, Sustain
63. Poka-yoke means:
Correct answer: A. Mistake-proofing
64. SMED aims to:
Correct answer: D. Reduce setup or changeover time
65. Value stream mapping is used to:
Correct answer: B. Visualise material and information flow to find waste
66. FMEA stands for:
Correct answer: C. Failure Mode and Effects Analysis
67. In FMEA, RPN equals:
Correct answer: B. Severity x Occurrence x Detection
68. APQP is a framework for:
Correct answer: B. Advanced product quality planning
69. PPAP is used to:
Correct answer: C. Approve production parts from suppliers
70. Design of Experiments (DOE) helps to:
Correct answer: A. Determine how factors affect a response efficiently
71. A factorial experiment studies:
Correct answer: B. Multiple factors and their interactions together
72. Measurement System Analysis (MSA) evaluates:
Correct answer: D. The accuracy and precision of measurement systems
73. Gage R&R assesses:
Correct answer: B. Repeatability and reproducibility of measurements
74. Accuracy refers to:
Correct answer: D. Closeness of a measurement to the true value
75. Precision refers to:
Correct answer: B. Consistency of repeated measurements
Questions 76 to 100
76. Calibration ensures that:
Correct answer: D. Instruments measure correctly against known standards
77. Acceptance sampling is used to:
Correct answer: D. Decide whether to accept a lot based on a sample
78. AQL stands for:
Correct answer: B. Acceptable Quality Level (or Limit)
79. Producer’s risk is the risk of:
Correct answer: B. Rejecting a good lot
80. Consumer’s risk is the risk of:
Correct answer: A. Accepting a bad lot
81. An OC curve shows:
Correct answer: D. Probability of accepting lots at different quality levels
82. Supplier quality management involves:
Correct answer: A. Selecting, monitoring and developing suppliers
83. A quality manual documents:
Correct answer: B. The scope and structure of the quality management system
84. Document control ensures:
Correct answer: C. Only current approved documents are in use
85. Traceability allows:
Correct answer: B. Tracking a product’s history, location and components
86. Customer satisfaction can be measured through:
Correct answer: A. Surveys, complaints and retention data
87. Voice of the Customer (VOC) captures:
Correct answer: D. Customer needs and expectations
88. Quality Function Deployment (QFD) translates:
Correct answer: A. Customer requirements into design specifications
89. Reliability is:
Correct answer: A. The probability a product performs without failure for a specified time
90. MTBF stands for:
Correct answer: D. Mean Time Between Failures
91. The bathtub curve describes:
Correct answer: C. Failure rate over a product’s life
92. A quality engineer’s role includes:
Correct answer: D. Designing and improving processes to meet quality requirements
93. Benchmarking compares:
Correct answer: D. Processes or performance against best practices
94. Hypothesis testing in quality is used to:
Correct answer: D. Decide statistically whether a difference is significant
95. Normal distribution is:
Correct answer: A. A symmetric bell-shaped distribution
96. Standard deviation measures:
Correct answer: B. Spread of data around the mean
97. Regression analysis models:
Correct answer: B. Relationships between input and output variables
98. Quality audits should be:
Correct answer: A. Objective, evidence-based and independent where possible
99. A run chart plots:
Correct answer: D. Data points over time without control limits
100. Management review in ISO 9001 is performed by:
Correct answer: C. Top management to assess the QMS
How to Pass the Certified Quality Engineer Exam
- Read every question carefully; most options look similar, so look for the most precise answer.
- Revise the questions above topic by topic rather than memorising letters, because option order can change in the live test.
- You need 80 correct answers out of 100 to pass, so aim to understand at least 85 to stay safe.
- If you do not clear it on the first attempt, review the questions you missed and use the retake option.
Frequently Asked Questions
How many questions are in the Certified Quality Engineer Professional Certification exam?
The exam has 100 multiple-choice questions, each worth 1 mark.
What is the passing score for the Certified Quality Engineer Professional Certification?
You need at least 80% (80 out of 100) to pass and receive the certificate.
Can I retake the Certified Quality Engineer Professional Certification exam?
Yes. If you score below 80%, you can retry the test after reviewing the topics.
Is the Itronix certificate verifiable?
Yes. Every certificate issued by Itronix Solutions has a unique ID that can be checked on the Itronix verify-certificate page.
More Programming & Development Certification Answers
- Advanced Java Certification Exam Answers
- Android Development Certification Exam Answers
- Automation Testing Certification Exam Answers
- Blockchain Certification Exam Answers
- C & C++ Programming Language Certification Exam Answers
- Core Java Programming Professional Certification Exam Answers
- Data Structures and Algorithm Certification Exam Answers
- Database Management System DBMS Certification Exam Answers
Disclaimer: These answers are provided for learning and revision. Questions and answers are checked regularly; if you find a mistake, let us know in the comments.
Priya Dogra – Free Certifications, Exam Answers & Career Guides Free certification exam answers, courses, scholarships and career guides for learners worldwide