Wednesday , November 18 2026
Breaking News

IT Networking Certification Exam Answers 2026 (All 100 Questions)

IT Networking Certification exam answers 2026: This page lists all 100 questions of the official IT Networking Certification exam by Itronix Solutions, each with its four answer options and the correct answer highlighted in green. Use it to revise every topic before you attempt the test and earn your verifiable certificate.

About this certification: A computer network is a system that connects numerous independent computers in order to share information (data) and resources.

Certification IT Networking Certification
Provider Itronix Solutions
Category Cyber Security & Networking
Total questions 100 multiple-choice questions
Marks 1 mark per question (100 marks)
Passing score 80% (80 out of 100)
Retake Available if you do not pass
Certificate Verifiable online certificate

Take the exam: IT Networking Certification on Itronix Solutions. See every other Itronix exam in our complete list of Itronix certification answers.

IT Networking Exam Questions and Answers

Questions 1 to 25

1. What does PoP stand for?

A. Post Office Protocol ✔
B. Pre Office Protocol
C. Protocol of Post
D. None

Correct answer: A. Post Office Protocol

2. What is the port number of PoP?

A. 35
B. 110 ✔
C. 25
D. 43

Correct answer: B. 110

3. What is the number of layers in the OSI model?

A. 2 layers
B. 4 layers
C. 7 layers ✔
D. 9 layers

Correct answer: C. 7 layers

4. The full form of OSI is?

A. Operating System interface
B. Operating System Internet
C. Optical System interconnection
D. Open system interconnection ✔

Correct answer: D. Open system interconnection

5. Identify the layer which provides service to the user.

A. Session layer
B. Presentation error
C. Physical layer
D. Application layer ✔

Correct answer: D. Application layer

6. A_______ is used to transfer data packets between two computer networks.

A. Router ✔
B. Switch
C. Brouter
D. Gateway

Correct answer: A. Router

7. Which of the following malicious program do not replicate automatically?

A. Zombie
B. Trojan Horse ✔
C. Virus
D. Worm

Correct answer: B. Trojan Horse

8. A computer in a network that cannot be accessed outside of the local network unless given permission is called __________.

A. Middleware
B. Internet
C. Intranet ✔
D. Modern

Correct answer: C. Intranet

9. A _________ device is used to connect multiple nodes to network.

A. router
B. modem
C. repeater
D. hub ✔

Correct answer: D. hub

10. What is the full form of DHCP in networking system?

A. Dynamic Host Configuration Protocol ✔
B. Display House Control Protocol
C. Data Host Control Panel
D. Dynamic Host Control Point

Correct answer: A. Dynamic Host Configuration Protocol

11. Which of these is a standard interface for serial data transmission?

A. RS232C ✔
B. ASCII
C. Centronics
D. 2

Correct answer: A. RS232C

12. What kind of transmission medium is most appropriate to carry data in a computer network that is exposed to electrical interferences?

A. Unshielded twisted pair
B. Optical fiber ✔
C. Coaxial cable
D. Microwave

Correct answer: B. Optical fiber

13. "Parity bits" are used for which of the following purposes?

A. Encryption of data
B. To transmit faster
C. To detect errors ✔
D. To identify the user

Correct answer: C. To detect errors

14. Which of the following transmission directions listed is not a legitimate channel?

A. Simplex
B. Half Duplex
C. Full Duplex
D. Double Duplex ✔

Correct answer: D. Double Duplex

15. Which type of topology is best suited for large businesses which must carefully control and coordinate the operation of distributed branch outlets?

A. Ring
B. Local area
C. Hierarchical
D. Star ✔

Correct answer: D. Star

16. When collection of various computers seems a single coherent system to its client, then it is called _________

A. distributed system ✔
B. computer network
C. networking system
D. mail system

Correct answer: A. distributed system

17. Two devices are in network if __________

A. a process is active and another is inactive
B. a process in one device is able to exchange information with a process in another device ✔
C. a process is running on both devices
D. PIDs of the processes running of different devices are same

Correct answer: B. a process in one device is able to exchange information with a process in another device

18. Which of the following computer networks is built on the top of another network?

A. chief network
B. prime network
C. overlay network ✔
D. prior network

Correct answer: C. overlay network

19. In computer network nodes are _________

A. the computer that originates the data
B. the computer that terminates the data
C. the computer that routes the data
D. all of the mentioned ✔

Correct answer: D. all of the mentioned

20. Communication channel is shared by all the machines on the network in ________

A. broadcast network ✔
B. unicast network
C. multicast network
D. anycast network

Correct answer: A. broadcast network

21. Cisco IOS is:

A. The operating system used on many Cisco routers and switches ✔
B. A web browser
C. A database
D. A cloud service

Correct answer: A. The operating system used on many Cisco routers and switches

22. User EXEC mode on a Cisco device is indicated by the prompt:

A. Router#
B. Router$
C. Router> ✔
D. Router(config)#

Correct answer: C. Router>

23. Privileged EXEC mode is entered with the command:

A. configure
B. start
C. login
D. enable ✔

Correct answer: D. enable

24. Global configuration mode is entered with:

A. show run
B. write memory
C. configure terminal ✔
D. enable secret

Correct answer: C. configure terminal

25. The command to view the active configuration is:

A. display all
B. show running-config ✔
C. show startup
D. list config

Correct answer: B. show running-config

Questions 26 to 50

26. The command to save the configuration is:

A. save all
B. store config
C. backup now
D. copy running-config startup-config ✔

Correct answer: D. copy running-config startup-config

27. The enable secret command:

A. Shows the configuration
B. Deletes passwords
C. Sets an encrypted password for privileged mode ✔
D. Restarts the router

Correct answer: C. Sets an encrypted password for privileged mode

28. service password-encryption:

A. Creates VLANs
B. Encrypts all traffic
C. Obscures plain-text passwords in the configuration ✔
D. Disables passwords

Correct answer: C. Obscures plain-text passwords in the configuration

29. show ip interface brief displays:

A. MAC table
B. A summary of interfaces, IP addresses and status ✔
C. VLANs
D. The routing table only

Correct answer: B. A summary of interfaces, IP addresses and status

30. The no shutdown command:

A. Disables an interface
B. Enables an interface ✔
C. Reboots the device
D. Deletes the config

Correct answer: B. Enables an interface

31. A /26 subnet mask equals:

A. 255.255.255.192 ✔
B. 255.255.255.128
C. 255.255.255.0
D. 255.255.255.224

Correct answer: A. 255.255.255.192

32. A /26 network provides how many usable hosts?

A. 30
B. 64
C. 62 ✔
D. 126

Correct answer: C. 62

33. A /30 subnet is commonly used for:

A. Large LANs
B. Wi-Fi only
C. Point-to-point links with 2 usable hosts ✔
D. Broadcast networks

Correct answer: C. Point-to-point links with 2 usable hosts

34. The network address of 192.168.10.70/26 is:

A. 192.168.10.128
B. 192.168.10.70
C. 192.168.10.64 ✔
D. 192.168.10.0

Correct answer: C. 192.168.10.64

35. The broadcast address of 192.168.10.64/26 is:

A. 192.168.10.255
B. 192.168.10.65
C. 192.168.10.127 ✔
D. 192.168.10.64

Correct answer: C. 192.168.10.127

36. VLSM allows:

A. Only one mask everywhere
B. Using different subnet mask lengths within the same network ✔
C. Only IPv6
D. No subnetting

Correct answer: B. Using different subnet mask lengths within the same network

37. Private IPv4 ranges include:

A. All addresses
B. 8.8.8.0/24 only
C. 1.1.1.0/24
D. 10.0.0.0/8, 172.16.0.0/12 and 192.168.0.0/16 ✔

Correct answer: D. 10.0.0.0/8, 172.16.0.0/12 and 192.168.0.0/16

38. An IPv6 address is written in:

A. Binary only
B. Dotted decimal
C. Letters only
D. Hexadecimal groups separated by colons ✔

Correct answer: D. Hexadecimal groups separated by colons

39. IPv6 link-local addresses start with:

A. FF00::
B. 192.168
C. FE80::/10 ✔
D. 2001::

Correct answer: C. FE80::/10

40. The double colon (::) in IPv6 represents:

A. A broadcast
B. A port
C. An error
D. One or more consecutive groups of zeros ✔

Correct answer: D. One or more consecutive groups of zeros

41. A routing table contains:

A. MAC addresses only
B. User passwords
C. Destination networks and how to reach them ✔
D. DHCP leases

Correct answer: C. Destination networks and how to reach them

42. A directly connected route appears when:

A. An interface is configured with an IP and is up ✔
B. A static route is added
C. OSPF runs
D. DNS works

Correct answer: A. An interface is configured with an IP and is up

43. A static route is configured with:

A. router ospf
B. ip route destination mask next-hop ✔
C. switchport mode
D. vlan 10

Correct answer: B. ip route destination mask next-hop

44. A default route is written as:

A. 255.255.255.255 0.0.0.0
B. 0.0.0.0 0.0.0.0 next-hop ✔
C. 192.168.1.0
D. 127.0.0.1

Correct answer: B. 0.0.0.0 0.0.0.0 next-hop

45. Administrative distance indicates:

A. Bandwidth
B. Physical cable length
C. Number of hops only
D. The trustworthiness of a routing source ✔

Correct answer: D. The trustworthiness of a routing source

46. OSPF is a:

A. Switching protocol
B. Link-state routing protocol ✔
C. Distance-vector protocol only
D. DNS protocol

Correct answer: B. Link-state routing protocol

47. OSPF uses which metric?

A. Delay only
B. Hop count
C. Cost based on bandwidth ✔
D. Random value

Correct answer: C. Cost based on bandwidth

48. OSPF routers in a single area must share:

A. The same area ID, such as area 0 ✔
B. No IDs
C. Different area IDs always
D. Only hostnames

Correct answer: A. The same area ID, such as area 0

49. RIP uses which metric?

A. Hop count ✔
B. Bandwidth
C. Delay
D. Cost

Correct answer: A. Hop count

50. The maximum hop count in RIP is:

A. 100
B. 15 ✔
C. 255
D. 7

Correct answer: B. 15

Questions 51 to 75

51. EIGRP is a:

A. Link-state only protocol
B. Switching protocol
C. Cisco advanced distance-vector routing protocol ✔
D. Wireless protocol

Correct answer: C. Cisco advanced distance-vector routing protocol

52. BGP is used to route:

A. Between VLANs only
B. Wi-Fi traffic
C. Between autonomous systems on the internet ✔
D. Within a single LAN only

Correct answer: C. Between autonomous systems on the internet

53. A switch learns MAC addresses by:

A. Using DHCP
B. Asking DNS
C. Reading the source MAC of incoming frames ✔
D. Pinging hosts

Correct answer: C. Reading the source MAC of incoming frames

54. The MAC address table is viewed with:

A. show ip route
B. show arp only
C. show mac address-table ✔
D. show vlan route

Correct answer: C. show mac address-table

55. An unknown unicast frame on a switch is:

A. Flooded out all ports except the incoming one ✔
B. Sent to the router only
C. Encrypted
D. Dropped always

Correct answer: A. Flooded out all ports except the incoming one

56. VLANs separate:

A. Collision domains only
B. Power circuits
C. Physical cables
D. Broadcast domains on a switch ✔

Correct answer: D. Broadcast domains on a switch

57. The command to create VLAN 10 is:

A. add vlan 10
B. new vlan 10
C. vlan 10 ✔
D. create vlan 10

Correct answer: C. vlan 10

58. An access port carries:

A. Multiple VLANs tagged
B. Traffic for a single VLAN ✔
C. Only management traffic
D. No traffic

Correct answer: B. Traffic for a single VLAN

59. A trunk port carries:

A. Only one VLAN
B. Traffic for multiple VLANs ✔
C. No VLANs
D. Only power

Correct answer: B. Traffic for multiple VLANs

60. IEEE 802.1Q is:

A. The standard for VLAN tagging on trunks ✔
B. An Ethernet speed
C. A routing protocol
D. A Wi-Fi standard

Correct answer: A. The standard for VLAN tagging on trunks

61. The native VLAN on an 802.1Q trunk is:

A. Never used
B. Sent untagged ✔
C. Tagged twice
D. Always encrypted

Correct answer: B. Sent untagged

62. Inter-VLAN routing can be done with:

A. Only cables
B. Only access points
C. Only hubs
D. A router-on-a-stick or a Layer 3 switch ✔

Correct answer: D. A router-on-a-stick or a Layer 3 switch

63. Router-on-a-stick uses:

A. Multiple physical routers
B. Subinterfaces on one router interface trunked to a switch ✔
C. Hubs
D. Wireless bridges

Correct answer: B. Subinterfaces on one router interface trunked to a switch

64. Spanning Tree Protocol (STP) prevents:

A. Layer 2 loops ✔
B. DNS failures
C. Slow Wi-Fi
D. IP conflicts

Correct answer: A. Layer 2 loops

65. The STP root bridge is elected based on:

A. The lowest bridge ID ✔
B. The newest switch
C. The highest IP
D. The fastest port

Correct answer: A. The lowest bridge ID

66. Rapid PVST+ provides:

A. Wireless roaming
B. Routing between VLANs
C. DHCP
D. Faster convergence of spanning tree per VLAN ✔

Correct answer: D. Faster convergence of spanning tree per VLAN

67. PortFast is used on:

A. Fibre links only
B. Trunk links between switches
C. Access ports connected to end devices ✔
D. Router uplinks only

Correct answer: C. Access ports connected to end devices

68. EtherChannel combines:

A. Two routers
B. Two VLANs
C. Wi-Fi and Ethernet
D. Multiple physical links into one logical link ✔

Correct answer: D. Multiple physical links into one logical link

69. LACP is:

A. A standard protocol for negotiating EtherChannel ✔
B. A VLAN tag
C. A Wi-Fi channel
D. A routing protocol

Correct answer: A. A standard protocol for negotiating EtherChannel

70. CDP and LLDP are used to:

A. Assign IPs
B. Discover directly connected neighbouring devices ✔
C. Route packets
D. Encrypt traffic

Correct answer: B. Discover directly connected neighbouring devices

71. DHCP DORA stands for:

A. Domain, Object, Resource, Access
B. None
C. Discover, Offer, Request, Acknowledge ✔
D. Data, Output, Route, Address

Correct answer: C. Discover, Offer, Request, Acknowledge

72. A DHCP relay (ip helper-address) is needed when:

A. Clients and the DHCP server are on different subnets ✔
B. No DHCP exists
C. They are on the same subnet
D. Using static IPs only

Correct answer: A. Clients and the DHCP server are on different subnets

73. NAT overload (PAT) allows:

A. Many private hosts to share one public IP using ports ✔
B. One host per public IP only
C. Only IPv6
D. No translation

Correct answer: A. Many private hosts to share one public IP using ports

74. Static NAT maps:

A. No addresses
B. Only ports
C. Many to one
D. One private IP to one public IP permanently ✔

Correct answer: D. One private IP to one public IP permanently

75. Standard ACLs filter traffic based on:

A. Application data
B. Source and destination ports
C. Source IP address only ✔
D. MAC addresses only

Correct answer: C. Source IP address only

Questions 76 to 100

76. Extended ACLs can filter on:

A. Only MAC
B. Only source IP
C. Source, destination, protocol and port ✔
D. Only VLAN

Correct answer: C. Source, destination, protocol and port

77. Standard ACLs should be placed:

A. Close to the destination ✔
B. Close to the source
C. On every port
D. Nowhere

Correct answer: A. Close to the destination

78. Extended ACLs should be placed:

A. Close to the source ✔
B. Only on servers
C. Only on switches
D. Close to the destination

Correct answer: A. Close to the source

79. Every ACL ends with an implicit:

A. Forward all
B. Permit any
C. Deny any ✔
D. Log all

Correct answer: C. Deny any

80. SSH should be used instead of Telnet for device management because:

A. Telnet is faster and secure
B. Telnet is newer
C. SSH has no authentication
D. SSH encrypts the session ✔

Correct answer: D. SSH encrypts the session

81. NTP is used on network devices to:

A. Route traffic
B. Encrypt passwords
C. Assign IPs
D. Synchronise clocks for accurate logs ✔

Correct answer: D. Synchronise clocks for accurate logs

82. Syslog is used to:

A. Resolve names
B. Assign VLANs
C. Route packets
D. Send device log messages to a central server ✔

Correct answer: D. Send device log messages to a central server

83. SNMP is used for:

A. Video calls
B. Monitoring and managing network devices ✔
C. Email delivery
D. File transfer

Correct answer: B. Monitoring and managing network devices

84. QoS on networks prioritises:

A. Time-sensitive traffic like voice and video ✔
B. Large downloads always
C. Spam
D. Backups only

Correct answer: A. Time-sensitive traffic like voice and video

85. Wireless LAN controllers manage:

A. Multiple lightweight access points centrally ✔
B. Routing between ISPs
C. Server storage
D. DNS zones

Correct answer: A. Multiple lightweight access points centrally

86. SSID is:

A. The name of a wireless network ✔
B. A MAC address
C. An IP range
D. A password hash

Correct answer: A. The name of a wireless network

87. WPA2-Enterprise uses:

A. A shared password only
B. No authentication
C. Open access
D. 802.1X authentication with a RADIUS server ✔

Correct answer: D. 802.1X authentication with a RADIUS server

88. SDN separates:

A. IPv4 from IPv6
B. Users from devices
C. Wi-Fi from Ethernet
D. The control plane from the data plane ✔

Correct answer: D. The control plane from the data plane

89. Network automation tools such as Ansible help to:

A. Disable logging
B. Paint cables
C. Replace routers
D. Configure many devices consistently via scripts ✔

Correct answer: D. Configure many devices consistently via scripts

90. REST APIs and JSON are used in modern networks for:

A. Power supply
B. Fan control
C. Programmatic device management ✔
D. Physical cabling

Correct answer: C. Programmatic device management

91. HSRP or VRRP provides:

A. Wireless encryption
B. DNS caching
C. First-hop gateway redundancy ✔
D. VLAN tagging

Correct answer: C. First-hop gateway redundancy

92. A collision domain is reduced by:

A. Using more hubs
B. Fewer routers
C. Using switches instead of hubs ✔
D. Longer cables

Correct answer: C. Using switches instead of hubs

93. A broadcast domain is separated by:

A. Routers or VLANs ✔
B. Repeaters
C. Cables
D. Hubs

Correct answer: A. Routers or VLANs

94. show ip route displays:

A. VLAN membership
B. Interface counters only
C. The MAC address table
D. The routing table ✔

Correct answer: D. The routing table

95. show vlan brief displays:

A. ARP cache
B. DNS records
C. VLANs and their assigned ports ✔
D. Routing table

Correct answer: C. VLANs and their assigned ports

96. The OSI layer responsible for routing is:

A. Layer 2 Data Link
B. Layer 7 Application
C. Layer 3 Network ✔
D. Layer 4 Transport

Correct answer: C. Layer 3 Network

97. Troubleshooting connectivity often follows:

A. Replacing all devices
B. Ignoring documentation
C. Random guessing
D. A layered approach from physical upward ✔

Correct answer: D. A layered approach from physical upward

98. CCNA certifies:

A. Cloud accounting
B. Graphic design
C. Video editing
D. Foundational networking knowledge on Cisco technologies ✔

Correct answer: D. Foundational networking knowledge on Cisco technologies

99. Port security violation mode shutdown:

A. Creates VLANs
B. Puts the port into err-disabled state on violation ✔
C. Increases speed
D. Ignores violations

Correct answer: B. Puts the port into err-disabled state on violation

100. The hostname command on a Cisco device:

A. Deletes config
B. Restarts it
C. Shows the IP
D. Sets the device name ✔

Correct answer: D. Sets the device name

How to Pass the IT Networking Exam

  • Read every question carefully; most options look similar, so look for the most precise answer.
  • Revise the questions above topic by topic rather than memorising letters, because option order can change in the live test.
  • You need 80 correct answers out of 100 to pass, so aim to understand at least 85 to stay safe.
  • If you do not clear it on the first attempt, review the questions you missed and use the retake option.

Frequently Asked Questions

How many questions are in the IT Networking Certification exam?

The exam has 100 multiple-choice questions, each worth 1 mark.

What is the passing score for the IT Networking Certification?

You need at least 80% (80 out of 100) to pass and receive the certificate.

Can I retake the IT Networking Certification exam?

Yes. If you score below 80%, you can retry the test after reviewing the topics.

Is the Itronix certificate verifiable?

Yes. Every certificate issued by Itronix Solutions has a unique ID that can be checked on the Itronix verify-certificate page.

More Cyber Security & Networking Certification Answers

Disclaimer: These answers are provided for learning and revision. Questions and answers are checked regularly; if you find a mistake, let us know in the comments.

About Priya Dogra

Priya Dogra runs priyadogra.com, where she shares free certification courses, internships, jobs, scholarships and exam preparation guides for Indian students and freshers. Follow her on YouTube, LinkedIn and Instagram for the latest opportunities.

Check Also

Unix/ Linux Certification exam answers 2026

Unix/ Linux Certification Exam Answers 2026 (All 100 Questions)

All 100 Unix/ Linux Certification exam questions with correct answers highlighted - updated 2026.

Leave a Reply

Your email address will not be published. Required fields are marked *